Home
Current Affairs January 2024

What is the correct answer?

4

Shear stress theory is applicable for

A. Ductile materials

B. Brittle materials

C. Elastic materials

D. All of the above

Correct Answer :

A. Ductile materials


Related Questions

What is the correct answer?

4

The spring mostly used in gramophones is

A. Helical spring

B. Conical spring

C. Flat spiral spring

D. Volute spring

What is the correct answer?

4

During hot working of metals,

A. Porosity of the metal is largely eliminated

B. Grain structure of the metal is refined

C. Mechanical properties are improved due of refinement of grains

D. All of the above

What is the correct answer?

4

In order to ensure self locking in a screw jack, it is essential that helix angle is __________ friction angle.

A. Larger than

B. Smaller than

C. Equal to

D. None of these

What is the correct answer?

4

If a load W is applied instantaneously on a bar; Then the stress induced in bar will

A. Be independent of ratio of mass of load W to mass of bar (y)

B. Increase with increase in y

C. Decrease with decrease in y

D. Depend on other considerations

What is the correct answer?

4

The rolling contact bearings are known as

A. Thick lubricated bearings

B. Plastic bearings

C. Antifriction bearings

D. Thin lubricated bearings

What is the correct answer?

4

A tapered key which fits in a key-way in the hub and is flat on the shaft, is known as

A. Woodruff key

B. Feather key

C. Flat saddle key

D. Gib head key

What is the correct answer?

4

Spring stiffness is

A. Ratio of coil diameter to wire diameter

B. Load required to produce unit deflection

C. Its capability of storing energy

D. Its ability to absorb shocks

What is the correct answer?

4

The condition for maximum power transmission is that the maximum tension in the flat belt should be equal to

A. 3 Pc

B. Pc

C. Pc/3

D. 2 Pc Where, Pc = tension in belt due to centrifugal force

What is the correct answer?

4

In designing a connecting rod, it is considered like __________ for buckling about Y-axis.

A. Both ends hinged

B. Both ends fixed

C. One end fixed and the other end hinged

D. One end fixed and the other end free

What is the correct answer?

4

The tension on the slack side of the belt is __________ the tension on the tight side of the belt.

A. Equal to

B. Less than

C. Greater than

D. None of these

What is the correct answer?

4

In order to have a connecting rod equally strong in buckling about X-axis and Y-axis, the moment of inertia about X-axis should be __________ the moment of inertia about Y-axis.

A. Equal to

B. Twice

C. Three times

D. Four times

What is the correct answer?

4

In V-belt drive, belt touches

A. At bottom

B. At sides only

C. Both at bottom and sides

D. Could touch anywhere

What is the correct answer?

4

When two springs are in series (having stiffness K), the equivalent stiffness will be

A. K

B. K/2

C. 2K

D. K/4

What is the correct answer?

4

The smallest diameter of an external or internal screw thread is known as

A. Minor diameter

B. Major diameter

C. Pitch diameter

D. None of these

What is the correct answer?

4

When screw threads are to be used in a situation where power is being transmitted in one direction only, then the screw threads suitable for this will be

A. Knuckle threads

B. Square threads

C. Acme threads

D. Buttress threads

What is the correct answer?

4

The sleeve or muff coupling is designed as a

A. Dun cylinder

B. Hollow shaft

C. Solid shaft

D. Thick cylinder

What is the correct answer?

4

In case of V-belt drive

A. The belt should touch the bottom of groove in the pulley

B. The belt should not touch the bottom of groove in the pulley

C. The belt should not touch the sides of groove in the pulley

D. None of the above

What is the correct answer?

4

The effective stress in wire ropes during normal working is equal to the stress due to

A. Axial load plus stress due to bending

B. Acceleration/retardation of masses plus stress due to bending

C. Axial load plus stress due to acceleration/retardation

D. Bending plus stress due to acceleration/retardation

What is the correct answer?

4

The period during which the cam follower remains at rest, when cam moves, is known as

A. Constant period

B. Fixed period

C. Dwell period

D. Idle period

What is the correct answer?

4

A sliding bearing in which although lubricant is present, the working surfaces __________ contact each other at least part of the time, is called boundary lubricated bearing.

A. Partially

B. Fully

C. Either A or B

D. None of these

What is the correct answer?

4

The dedendum circle diameter is equal to (where φ = Pressure angle)

A. Pitch circle diameter × cosφ

B. Addendum circle diameter × cosφ

C. Clearance circle diameter × cosφ

D. Pitch circle diameter × sinφ

What is the correct answer?

4

In a flange coupling, the bolts are subjected to

A. Tensile stress

B. Compressive stress

C. Shear stress

D. None of these

What is the correct answer?

4

When a hole of diameter d is punched in a metal of thickness 't', then the force required to punch a hole is equal to (where τu = Ultimate shear strength of the material of the plate)

A. d.t.τu

B. πd.t.τu

C. π/4 × d².τu

D. π/4 × d² × t.τu

What is the correct answer?

4

A column is known as a long column if the slenderness ratio is

A. 40

B. 50

C. 70

D. 100

What is the correct answer?

4

Factor of safety for fatigue loading is the ratio of

A. Elastic limit to the working stress

B. Elastic limit to the yield point

C. Endurance limit to the working stress

D. Young's modulus to the ultimate tensile strength

What is the correct answer?

4

The shear stress in a beam varies from zero at the outer fibres to a maximum at the________.

A. Neutral surface

B. Upper surface

C. Lower surface

D. None of these

What is the correct answer?

4

If P1 and P2 are the tight and slack side tensions in the belt, then the initial tension Pi (neglecting centrifugal tension) will be equal to

A. P1 - P2

B. P1 + P2

C. 2 × (P1 + P2)

D. [2 × (P1 + P2)] + Pc Where Pc is centrifugal tension

What is the correct answer?

4

When the length of the journal is equal to the diameter of the journal, then the bearing is said to be a

A. Short bearing

B. Long bearing

C. Medium bearing

D. Square bearing

What is the correct answer?

4

The expression 0.175 - 0.841/T is the Lewis form factor for

A. 14 ½° composite and full depth involute system

B. 20° full depth involute system

C. 20° stub system

D. None of the above

What is the correct answer?

4

The building up of worn and undersized parts, subjected to repeated loads by electroplating is

A. Best method

B. Extremely hazardous

C. Has no effect as regards fatigue strength

D. Cheapest method