Related Questions
What is the correct answer?
4
Cast iron contains __________ percent carbon.
What is the correct answer?
4
Which of the following does not have a sharp melting point?
What is the correct answer?
4
Breakeven point represents the condition, when the company runs under no profit no loss condition. In break even analysis, total cost comprises of fixed cost
What is the correct answer?
4
For separating small pieces of metal from engine oil of a car, the best separating technique is the
D. Fractional distillation
What is the correct answer?
4
Addition of silicon to cast iron
A. Promotes graphite module formation
B. Improves its ductility
C. Does not promote graphite flakes formation
D. Increases the fluidity of molten metal
What is the correct answer?
4
Pick out the wrong statement about coating/electroplating of metals.
A. Phosphate coating is used as an excellent base for paints & enamels
B. Phosphate coating is less corrosion resistant than chromate coating
C. The base metal to be electroplated is normally made the cathode of the electrolytic cell and coating metal is made the anode
D. Calorising is the process of coating steel with chromium
What is the correct answer?
4
Encyclopaedia of Chemical Technology has been
A. Authored by Kirk Othmer
B. Edited by Perry and Chilton
D. Authored by Perry and Chilton
What is the correct answer?
4
Which of the following metals is the most prone to work hardening?
What is the correct answer?
4
What is the value of included angle of a triangular notch for maximum discharge?
What is the correct answer?
4
Regeneration of molecular sieve requires it to be heated to a temperature of about __________ °C.
What is the correct answer?
4
__________ number determines whether the fluid flow in an open channel is supercritical, critical or sub-critical.
What is the correct answer?
4
Addition of __________ to steel does not help in improving its machinability.
What is the correct answer?
4
The main reducing agent in iron blast furnace is
What is the correct answer?
4
To improve the machinability of steel, it is generally subjected to
What is the correct answer?
4
Tempering of a material does not improve its
What is the correct answer?
4
Cold chisel & hammers are made of
What is the correct answer?
4
The boiling & freezing points on a newly defined temperature scale in degree 'D' are 400°D & 100°D respectively. The temperature reading corresponding to 60°C on this new temperature scale will be equal to __________ °D.
What is the correct answer?
4
A dense structure of grinding wheel is not used for the
What is the correct answer?
4
Dry saturated steam can be converted into superheated steam by
A. Increasing its cross-sectional area of flow
B. Passing it through a pressure reducing valve
C. Forcing it downwards through a vertical tube
What is the correct answer?
4
The effect of friction on the flow of steam through a nozzle is to decrease the __________ of steam.
What is the correct answer?
4
The two elements required to form substitutional solid solution should not have
A. Same crystalline structure
C. Widely differing electronegativity
What is the correct answer?
4
Projection welding & stud welding is categorised as the __________ welding.
What is the correct answer?
4
Powder metallurgy process does not make metal powder by
D. Electrolytic deposition
What is the correct answer?
4
With increase in annealing temperature, the following defect density decreases.
What is the correct answer?
4
The main charge in blast furnace is usually
C. Limestone, coke & iron ore
D. Limestone, sand & iron ore
What is the correct answer?
4
Which one of the following is incombustible?
What is the correct answer?
4
Maximum heat dissipation occurs from a steel wire (k = 0.5 W/m. k) of 15 mm diameter exposed to air (h = 20W/m2 .k), when the insulation thickness is __________ mm.
What is the correct answer?
4
Vernier calipers cannot be used to measure the
A. I.D. & O.D. of the shaft
D. Clearance between two mating surfaces
What is the correct answer?
4
__________ remains constant during the adiabatic cooling of moist air.
What is the correct answer?
4
With increase in temperature, the electrical conductivity of semiconductors
D. Either (A) or (B), depends on the type of semi-conductor