Related Questions
What is the correct answer?
4
When designing a home for a client, one of the most important predesign considerations that an architect needs to address is ________.
A. How much money the client is willing to spend
B. The site on which the house is to sit
C. The nearest grocery store
D. Whether or not there is a curb and gutter system
What is the correct answer?
4
This is used to indicate that a surface is to be machined:
What is the correct answer?
4
This is a conical-shaped recess around a hole, often used to receive a tapered screw head:
What is the correct answer?
4
The MASSPROP shortcut will provide the following information.
What is the correct answer?
4
This type of surface may be a plane, a single curved surface, or a warped surface:
What is the correct answer?
4
The first step in creating a traditional technical drawing is to ________.
A. Draw a series of guide lines
C. Align the paper so that it will be positioned square to the parallel bar
D. Sharpen the leads in the technical pens
What is the correct answer?
4
A half-moon protractor is divided into how many degrees?
What is the correct answer?
4
A fillet is a rounded surface on the ________ corner of a part.
What is the correct answer?
4
When drawing a line using the relative coordinate system a line is created from ________.
B. The ending point of the last line
C. The beginning point of the last line
What is the correct answer?
4
When creating a block the drafter needs to pay particular attention to selecting a base point because it determines the ________.
What is the correct answer?
4
In some circumstances an entire drawing can be inserted into a different drawing as a block. When this is used the base point will default to ________.
What is the correct answer?
4
Drafters should use a ________ in a section view of a mechanical part that includes the cylindrical view of a threaded hole.
What is the correct answer?
4
Switches and relays should be shown in this position with no operating force or applied energy:
What is the correct answer?
4
Isometric drawings are often used by ________ to help illustrate complex designs.
What is the correct answer?
4
These are lines drawn on a map to locate, in the plan view, points of equal ground elevation:
What is the correct answer?
4
The architectural drafter usually begins a set of working drawings by creating the ________ plan first.
What is the correct answer?
4
Architectural drawings used to construct a house are often plotted with a scale of ¼ = 1'-0. What scale is this?
What is the correct answer?
4
In this type of view, the cutting plane line indicates both the location of the cutting plane and the direction of sight:
What is the correct answer?
4
When the receding lines are true length, and the projectors are at 45 degrees to the plane of projection, the oblique drawing is called this:
C. Axonometric projection
What is the correct answer?
4
A drafter who develops technical drawings of a highway overpass would most likely be a ________ drafter.
What is the correct answer?
4
In this type of dimensioning, allowance must be made for bends:
What is the correct answer?
4
In this type of drawing, vertical pipes may be revolved into the horizontal plane:
What is the correct answer?
4
The text used on a typical detail sheet should be ________.
C. In an architectural text style
What is the correct answer?
4
The 3-D commands on the Modeling toolbar include ________.
What is the correct answer?
4
In this type of concrete, the steel is pre-tensioned before the superimposed load is applied:
What is the correct answer?
4
Some traditional board drafters preferred the drafting machine over the parallel straight edge because it could be used without the need for________.
What is the correct answer?
4
The most common geometric form used in gears today is this:
What is the correct answer?
4
When using the descriptive geometry method to create an auxiliary view the drafter should __________.
A. Rotate the snap grid to the same angle of the inclined plane
B. Offset the right vertical line of the front view
C. Rotate the top line of the front view 45 degrees
D. Offset the top line of the front view 2 inches
What is the correct answer?
4
This type of auxiliary view is projected onto a plane that is perpendicular to one of the principal planes of projection:
What is the correct answer?
4
Center lines are used to locate or represent the centers of ________.