Related Questions
What is the correct answer?
4
RIP supports load balancing for up to __________ ___________ paths.
What is the correct answer?
4
Which of the following is true concerning RIPv2?
A. It uses triggered updates.
D. It doesn't support route summarization
What is the correct answer?
4
RIP has a maximum hop count of ____________ hops.
What is the correct answer?
4
Which router command would take you back to a suspended telnet session?
What is the correct answer?
4
IGRP generates an update every ___________ seconds.
What is the correct answer?
4
Which protocol supports VLSM?
What is the correct answer?
4
You are given a MAC address of 01A2.0482.FE12. What is the OUI value in binary?
A. 00011011.10100010.00000100
B. 00000000.00000001.00000100
C. 00000001.10100010.00000100
D. 00000001.10100001.00000010
What is the correct answer?
4
On the 1900 switch, how do you enter User EXEC mode?
A. It comes up by default.
B. Enter the letter U in the menu.
C. Enter the letter K in the menu.
D. Enter the letter C in the menu.
What is the correct answer?
4
A _________ uses Gigabit Ethernet as a media type
What is the correct answer?
4
_________ defines how the Frame Relay DTE and DCE interact with each other.
What is the correct answer?
4
You are given a Class C network with 25 bits of networking. How many subnets do you have?
What is the correct answer?
4
You have a total of five routers. ________ circuits are required to fully mesh the network, where every router needs ___________ interfaces.
What is the correct answer?
4
Which command takes you from Privilege EXEC mode to User EXEC mode?
What is the correct answer?
4
Which metric components, by default, are used in IGRP? (Choose all the correct answers.)
What is the correct answer?
4
Which control sequence moves the cursor to the end of the line?
What is the correct answer?
4
Which router command clears all of the static translations in the address translation table?
A. erase ip nat translation *
B. clear ip nat translation *
C. clear ip nat translation all
D. None of these commands
What is the correct answer?
4
The switch port that is chosen to forward traffic for a segment is called a __________.
What is the correct answer?
4
A routing protocol will use a _________ to determine which path is the best path.
A. Administrative distance
What is the correct answer?
4
You are given a class C network, 192.168.1.0/24. You need one network with 120 hosts and three networks with 60 hosts. What subnet mask values would you use?
A. 255.255.255.128 and 255.255.255.192
What is the correct answer?
4
Which 2950 command assigns a VLAN to an interface?
A. vlan-membership static
C. switchport access vlan
D. switchport mode access
What is the correct answer?
4
A _________ is used to connect networking devices that are in a very close geographic area, such as a floor of a building, a building itself, or a campus environment.
What is the correct answer?
4
With _________ switching, the switch reads the destination MAC address of the frame and
immediately starts forwarding the frame.
What is the correct answer?
4
Which of the following is true concerning 802.1Q?
A. It supports hub connections.
B. It is supported on both the 1900 and 2950 switches.
C. The native VLAN is tagged.
D. The original Ethernet frame is not modified.
What is the correct answer?
4
Which command defines interesting traffic?
What is the correct answer?
4
How many steps do LCP and NCP go through when setting up a connection?
What is the correct answer?
4
When configuring the ip nat inside source command, which parameter must you specify to perform PAT?
What is the correct answer?
4
Private addressing is defined in RFC ______.
What is the correct answer?
4
Which would you use to move your cursor back one word?
What is the correct answer?
4
The ___________ converts an ISDN four-wire connection to a two-wire connection.
What is the correct answer?
4
VLSM allows you to summarize 192.168.2.0/24 and 192.168.3.0/24 as 192.168.2.0/25.