Related Questions
What is the correct answer?
4
Which of the following does not have a sharp melting point?
What is the correct answer?
4
A particle is settling in a liquid under Stokesian conditions. The free falling velocity of the particle is proportional to
What is the correct answer?
4
An oxidation process is accompanied with decrease in the
What is the correct answer?
4
Baffles provided on the shell side of a shell and tube heat exchanger are meant for
A. Providing support for the tubes
B. Improving heat transfer
D. Preventing the fouling of tubes & stagnation of shell side fluid
What is the correct answer?
4
The rolling process cannot be used to produce
What is the correct answer?
4
Dryness fraction of dry steam is
What is the correct answer?
4
The boiling & freezing points on a newly defined temperature scale in degree 'D' are 400°D & 100°D respectively. The temperature reading corresponding to 60°C on this new temperature scale will be equal to __________ °D.
What is the correct answer?
4
The most detrimental impurity in high pressure boiler feed water is
What is the correct answer?
4
Shaft/rotor speed is most accurately measured by a
What is the correct answer?
4
Normalising does not __________ of a metal.
A. Improve machinability & tensile strength
B. Remove internal stresses
D. Remove strains caused by cold working
What is the correct answer?
4
__________ cannot increase the fatigue strength of a material.
What is the correct answer?
4
Earing is a defect found in steels after the following metal working operation.
What is the correct answer?
4
Which of the following is prone to cup and cone fracture?
C. Round specimen of ductile metal
D. Flat tensile specimen of ductile metal
What is the correct answer?
4
High relative humidity decreases the evaporative process and as the temperature is increased, the relative humidity decreases. The comfort range for human body is the ambient temperature of 22 to 27°C with relative humidity ranging from __________ percent.
What is the correct answer?
4
In TIG welding, thoriated tungsten electrodes are used, because it
A. Has higher current carrying capacity
B. Has better electron emissivity
C. Is stronger than ordinary tungsten
What is the correct answer?
4
In electrical resistance welding, distortion results from the use of improper
What is the correct answer?
4
The bank of tubes located at the back of the domestic refrigerators are the __________ tubes.
What is the correct answer?
4
The minimum and the maximum number of members required to form a Private Limited Joint Stock Company are respectively
What is the correct answer?
4
The Al2O3 content of cryolite in Hall- Heroult cell is maintained between __________ percent.
What is the correct answer?
4
Transition from laminar to turbulent zone in free convection heat transfer is governed by the critical value of
B. Grashoff number & Reynolds number
D. Grashoff number & Prandtl number
What is the correct answer?
4
Friction factor for fluid flow in pipe does not depend upon the
C. Fluid density & viscosity
D. Mass flow rate of fluid
What is the correct answer?
4
Corrosion of metals cannot be prevented by its
What is the correct answer?
4
Good design of the casing of a centrifugal pump aims at minimising the
What is the correct answer?
4
Probability of cavitation occuring becomes very high, when the local __________ resulting in water bubbles formation, which on rupture cause cavitation
A. Pressure falls below the vapour pressure
B. Pressure becomes very high
C. Temperature becomes low
What is the correct answer?
4
Galvanic corrosion cannot be prevented by
C. Usage of largest possible anodic area
What is the correct answer?
4
Working of linear variable differential transducer (LVDT) is based on the principle of variable
What is the correct answer?
4
The highest stress that a material can withstand for a specified length of time without excessive deformation is called the __________ strength.
What is the correct answer?
4
Presence of nickel & chromium in steel does not raise its
What is the correct answer?
4
Difference at any instant between the value of the controlled variable and the set point is called the
What is the correct answer?
4
All of the following alloying elements of steel increases hardness but sacrifice ductility, except