Related Questions
What is the correct answer?
4
Diameter of the rivet to be provided on a 20 mm. thick boiler plate will be __________ mm.
What is the correct answer?
4
Thermal equivalent of electrical power in practical calculation is __________ kcal/kWh.
What is the correct answer?
4
For infinite parallel planes having emissivities ε1 & ε2, the interchange factor for radiation from surface 1 to surface 2 is given by
What is the correct answer?
4
The surface tension of a liquid, at critical temperature is
D. Same as that at any other temperature
What is the correct answer?
4
Which of the following fastening devices has a head at one end and a nut fitted to the other?
What is the correct answer?
4
Holes for riveting purposes should be preferably made by
What is the correct answer?
4
Babbitt lining is used on brass/bronze bearings to increase the
A. Antifriction properties
What is the correct answer?
4
Which of the following is not an explosive?
What is the correct answer?
4
As the fluid flow rate increases, the float of the Rotameter
B. Rotates at higher speed
C. Rotates at lower speed
D. Drops down in the tube
What is the correct answer?
4
A jig is used while __________ a hole.
What is the correct answer?
4
If a nuclear reactor produces more fissile nuclear fuel than it consumes, then it is called a __________ reactor.
What is the correct answer?
4
Silicon crystal can be converted to p-type semiconductor by doping with
What is the correct answer?
4
For dynamic strain measurement, the Wheatstone bridge used is of __________ type.
A. Voltage sensitive null
B. Voltage sensitive deflected
C. Current sensitive deflected
What is the correct answer?
4
In an eutectic system, two elements are completely
A. Soluble in solid state
B. Insoluble in liquid state
C. Insoluble in both solid & liquid state
D. Soluble in liquid state
What is the correct answer?
4
Routing in production, planning & control is concerned with the
A. Sequence of operation to be performed
B. Progress of work performed
C. Authorisation of work to be performed
D. Balancing of load on machines
What is the correct answer?
4
Insulation of liquid surface can be achieved by __________ on top of its surface.
A. Floating hollow polypropylene spheres
B. Spraying alumina powder
What is the correct answer?
4
Cold working of a material results in increase in hardness, which is termed as the __________ hardening.
What is the correct answer?
4
M10 index of coke indicates its
What is the correct answer?
4
Tumbling is the process of improving the __________ of the materials/parts.
What is the correct answer?
4
A form of stress corrosion failure termed as 'season cracking' is generally observed in
A. Thermosetting polymers
What is the correct answer?
4
Maximum consumption of limestone is in the __________ industry.
What is the correct answer?
4
Carnot cycle is also termed as the constant __________ cycle in thermodynamics.
What is the correct answer?
4
Viscoelastic behaviour is observed in __________ materials.
A. Non-crystalline organic polymeric
What is the correct answer?
4
Thermodynamic cycle involved in the working of a thermal power plant is the __________ cycle.
What is the correct answer?
4
Sacrificial anode method is used in the protection of pipelines which are buried underground. Sacrificial anode
A. Occurs higher in the electro-chemical series of metals
B. Is exemplified by magnesium plate
C. Is much cheaper than the cathodic base material to be guarded against corrosion
What is the correct answer?
4
When the wet steam is throttled but still remains wet at the exit of the throttle valve, then its temperature & dryness fraction respectively
What is the correct answer?
4
__________ has a negative co-efficient of linear expansion.
What is the correct answer?
4
According to thermodynamic Fahrenheit scale, the fundamental interval between ice point to steam point is
What is the correct answer?
4
Which of the following varies as the square root of oil pressure during atomisation of fuel oil through a pressure jet burner?
What is the correct answer?
4
The 'transition temperature' for ductile to brittle behaviour of steel increases with increase in the __________ content in steel.