Home
Current Affairs January 2024

What is the correct answer?

4

The Ackerman steering gear mechanism is preferred to the Davis steering gear mechanism, because

A. Whole of the mechanism in the Ackerman steering gear is on the back of the front wheels

B. The Ackerman steering gear consists of turning pairs

C. The Ackerman steering gear is most economical

D. Both (A) and (B)

Correct Answer :

D. Both (A) and (B)


Related Questions

What is the correct answer?

4

A friction circle is a circle drawn when a journal rotates in a bearing. Its radius depends upon the coefficient of friction and the

A. Magnitude of the forces on journal

B. Angular velocity of journal

C. Clearance between journal and bearing

D. Radius of journal

What is the correct answer?

4

Torsional vibrations are said to occur when the particles of a body moves

A. Perpendicular to its axis

B. Parallel to its axis

C. In a circle about its axis

D. None of these

What is the correct answer?

4

If the opposite links of a four bar linkage are equal, the links will always form a

A. Triangle

B. Rectangle

C. Parallelogram

D. Pentagon

What is the correct answer?

4

A shaft has two heavy rotors mounted on it. The transverse natural frequencies, considering each of the rotor separately, are 100 Hz and 200 Hz respectively. The lowest critical speed is

A. 5,367 r.p.m.

B. 6,000 r.p.m.

C. 9,360 r.p.m.

D. 12,000 r.p.m.

What is the correct answer?

4

In S.H.M., acceleration is proportional to

A. Velocity

B. Displacement

C. Rate of change of velocity

D. All of the above

What is the correct answer?

4

Which of the following statement is correct for involute gears?

A. The interference is inherently absent.

B. The variation in centre distance of shafts increases radial force.

C. A convex flank is always in contact with concave flank.

D. The pressure angle is constant throughout the teeth engagement.

What is the correct answer?

4

For simple harmonic motion of the of follower, a cosine curve represents

A. Displacement diagram

B. Velocity diagram

C. Acceleration diagram

D. All of the above

What is the correct answer?

4

A mechanism is an assemblage of

A. Two links

B. Three links

C. Four or more than four links

D. All of these

What is the correct answer?

4

A circle passing through the pitch point with its center at the center of cam axis is known as

A. Pitch circle

B. Base circle

C. Prime circle

D. Outer circle

What is the correct answer?

4

The acceleration of the reciprocating roller follower when it has contact with the straight flanks of the tangent cam, is given by

A. ω². (r₁ r₂). (1 - cos² θ)

B. ω². (r₁ + r₂). (1 + cos² θ)

C. ω². (r₁ + r₂). [(2 - cos² θ)/cos³ θ]

D. ω². (r₁ - r₂). (1 - sin² θ)

What is the correct answer?

4

The frictional torque transmitted by a cone clutch is same as that of

A. Flat pivot bearing

B. Flat collar bearing

C. Conical pivot bearing

D. Truncated conical pivot bearing

What is the correct answer?

4

A shaft has an attached disc at the centre of its length. The disc has its centre of gravity located at a distance of 2 mm from the axis of the shaft. When the shaft is allowed to vibrate in its natural bow-shaped mode, it has a frequency of vibration of 10 rad/s. When the shaft is rotated at 300 r.p.m., it will whirl with a radius of

A. 2 mm

B. 2.22 mm

C. 2.50 mm

D. 3.0 mm

What is the correct answer?

4

A single degree of freedom system is given by, m × (d²x/dt²) + c × (dx/dt) + sx = F.cosω.t with usual notations. It represents

A. Free vibration with damping

B. Free vibration without damping

C. Forced vibration with damping

D. Forced vibration without damping

What is the correct answer?

4

The coriolis component of acceleration exists whenever a point moves along a path that has

A. Linear displacement

B. Rotational motion

C. Gravitational acceleration

D. Tangential acceleration

What is the correct answer?

4

A slider crank chain consists of following numbers of turning and sliding pairs

A. 1, 3

B. 2, 2

C. 3, 1

D. 4, 0

What is the correct answer?

4

In a multiple V-belt drive, when a single belt is damaged, it is preferable to change the complete set to

A. Reduce vibration

B. Reduce slip

C. Ensure uniform loading

D. Ensure proper alignment

What is the correct answer?

4

The stress induced in a body will be shear stress, when it is subjected to

A. Longitudinal vibrations

B. Transverse vibrations

C. Torsional vibrations

D. None of these

What is the correct answer?

4

In the below figure, PC is the connecting rod and OC is the crank making an angle θ with the line of stroke PO and rotates with uniform angular velocity at ω rad/s. The Klien's acceleration diagram for determining the acceleration of the piston P is shown by quadrilateral CQNO, if N coincides with O, then

A. Acceleration and velocity of the piston P is zero

B. Acceleration and velocity of the piston P is maximum

C. Acceleration of the piston P is zero and its velocity is maximum

D. Acceleration of the piston P is maximum and its velocity is zero

What is the correct answer?

4

Which of the following is an example of a higher pair?

A. Toothed gearing

B. Belt and rope drive

C. Ball and roller bearing

D. All of these

What is the correct answer?

4

The frictional torque transmitted in a flat pivot bearing, considering uniform wear, is (where μ = Coefficient of friction, W = Load over the bearing, and R = Radius of bearing surface)

A. (1/2) μ W R

B. (2/3) μ W R

C. (3/4) μ W R

D. μ W R

What is the correct answer?

4

The example of lower pair is

A. Shaft revolving in a bearing

B. Straight line motion mechanisms

C. Automobile steering gear

D. All of the above

What is the correct answer?

4

Kinematic pairs are those which have

A. Point or line contact between the two elements when in motion

B. Surface contact between the two elements when in motion

C. Elements of pairs not held together mechanically

D. Two elements that permit relative motion

What is the correct answer?

4

The motion between a pair which takes place in __________ is known as incompletely constrained motion.

A. One direction only

B. Two directions only

C. More than one direction

D. None of these

What is the correct answer?

4

The number of centers in a crank driven slider crank mechanism is

A. 0

B. 2

C. 4

D. 6

What is the correct answer?

4

The equation of free vibrations of a system is (d²x/dt²) +36 π²x, its natural frequency is

A. 3 Hz

B. 3π Hz

C. 6 Hz

D. 6π Hz

What is the correct answer?

4

The pressure angle of a cam is the angle between the direction of the follower motion and a normal to the

A. Pitch circle

B. Base circle

C. Pitch curve

D. Prime circle

What is the correct answer?

4

The two elements of a pair are said to form a _________ when they permit relative motion between them.

A. Open pair

B. Kinematic pair

C. Sliding pair

D. None of these

What is the correct answer?

4

Rectilinear motion of piston is converted into rotary by

A. Cross head

B. Slider crank

C. Connecting rod

D. Gudgeon pin

What is the correct answer?

4

A point on a connecting link (excluding end points) of a double slider crank mechanism traces a

A. Straight line path

B. Hyperbolic path

C. Parabolic path

D. Elliptical path

What is the correct answer?

4

In a rigid link OA, velocity of A w.r.t. O will be

A. Parallel to OA

B. Perpendicular to OA

C. At 45° to OA

D. Along AO