The actual feed in centerless grinders is given by (where d = Dia. of regulating wheel, n = Revolutions per minute, and α = Angle of inclination of wheel)
πd
πdn
πdn sinα
πdn cosα
Correct Answer :
C. πdn sinα
Related Questions
The snag grinding is done
To produce good surface finish and high degree of accuracy
To remove considerable amount of metal without regard to accuracy of the finished surface
To grind exterior cylindrical surfaces
Any one of the above
In drilling aluminium, a drill with
Zero helix angle is used
Low helix angle is used
High helix angle is used
Any helix angle can be used
Which of the following operations can be performed with milling cutters?
Cutting key ways on shafts
Cutting external screw threads
Cutting teeth of spur gears
All of these
The cutting speed for drilling copper with high speed steel drills varies from
10 to 20 m/min
18 to 30 m/min
24 to 45 m/min
60 to 90 m/min
The cutting fluid mostly used for machining alloy steels is
Water
Soluble oil
Dry
Sulphurised mineral oil
In ECM, the material removal is due to
Corrosion
Erosion
Fusion
Ion displacement
The lead screw of a lathe has _________ threads.
Single start
Double start
Multi-start
Any one of these
The binding material used in cemented carbide tools is
Tungsten
Chromium
Silicon
Cobalt
In American Standard Association (A S A) system, if the tool nomenclature is 8-6-5-5-10-15-2 mm, then the side rake angle will be
5°
6°
8°
10°
Two 1 mm thick steel sheets are to be spot welded at a current of 5000 A. Assuming effective resistance to be 200 μm and current flow time of 0.2 second, heat generated during the process will be
0.2 Joule
1 Joule
5 Joule
1000 Joule
In drilling Bakelite and fibrous plastics, the point angle of a drill is
90°
118°
135°
150°
In electro-discharge machining, dielectric is used to
Help in the movement of the sparks
Control the spark discharges
Act as coolant
All of these
The increase in depth of cut and feed rate __________ surface finish.
Improves
Deteriorates
Does not effect
None of these
In a shaper
Tool is stationary and work reciprocates
Work is stationary and tool reciprocates
Tool moves over stationary work
Tool moves over reciprocating work
For generating a Coons surface we require
A set of grid points on the surface
A set of grid control points
Four bounding curves defining the surface
Two bounding curves and a set of grid control points
The main purpose of a boring operation, as compared to drilling, is to
Drill a hole
Finish the drilled hole
Correct the hole
Enlarge the existing hole
In metal cutting operations, the shear angle is the angle made by the shear plane with the
Direction of the tool axis
Direction of tool travel
Perpendicular to the direction of the tool axis
Central plane of the workpiece
Relief angles on high speed steel tools usually vary from
0° to 3°
3° to 10°
10° to 20°
20° to 30°
When the shear angle is large
Path of shear is short and chip is thin
Path of shear is large and chip is thick
Path of shear is short and chip is thick
Path of shear is large and chip is thin
In centreless grinding, the surface speed of regulating wheel is
5 to 15 m/min
15 to 60 m/min
60 to 90 m/min
90 to 120 m/min
In metal machining, the zone where the heat is generated due to friction between the moving chip and the tool face, is called
Friction zone
Work-tool contact zone
Shear zone
None of these
In an interchangeable assembly, shafts of size 25.000 -0.010⁺⁰⁰⁴⁰ mm mate with holes of size 25.000 -0.020⁺⁰⁰³⁰, the maximum interference (in microns) in the assembly is
40
30
20
10
When the tool moves parallel to the lathe axis, the movement is termed as
Cross feed
Angular feed
Longitudinal feed
Any one of these
For turning internal tapers, the suitable method is
By a form tool
By setting over the tail stock
By a taper turning attachment
By swivelling the compound rest
A dense structure of a grinding wheel is used for
Hard materials
Brittle materials
Finishing cuts
All of these
The capacity of a material to be welded under the imposed fabrication conditions into a specific, suitably designed structure and to perform satisfactorily in the intended service is known as?
Weldment
Weld tab
Weldability
Tack weld
Which type of motor is not used in axis or spindle drives of CNC machine tools?
Induction motor
DC servo motor
Stepper motor
Linear servo motor
A fixture is defined as a device which
Holds and locates a workpiece and guides and controls one or more cutting tools
Holds and locates a workpiece during an inspection or for a manufacturing operation
Is used to check the accuracy of workpiece
All of the above
Which of the following arc welding processes does not use consumable electrodes?
GMAW
GTAW
Submerged Arc Welding
None of these
When the temperature of a solid metal increases,
Strength of the metal decreases but ductility increases
Both strength and ductility of the metal decreases
Both strength and ductility of the metal increases
Strength of the metal increases but ductility decreases