The architectural and construction industries use the United States National CAD standard (NCS) system on many ________ projects.
Residential
Commercial
Aerospace
Publicly funded
Correct Answer :
D. Publicly funded
Related Questions
A round is a rounded surface on the ________ corner of a part.
Inside
Outside
Radial
Isoplane
One critical issue drafters need to pay close attention to is the ________.
Size of the sheet
Designer's intent
Scale factor
None of the above
An engineer's scale would be used to measure lines on a drawing where the scale factor reads ________.
1/4 = 1'-0
1/8 = 1'-0
1 = 100'
3/4 = 1'-0
When using versions of Auto-CAD prior to Release 2006 it may be necessary to ________ a block in order to edit it.
Copy
Explode
Offset
None of the above
Oblique sections are useful to show this:
Foreshortened features
Oblique lines
Interior shapes
Projected features
This line pattern is composed of three dashes, one long dash on each end with a short dash in the middle:
Object
Hidden
Center
Phantom
The condition of a part when it contains the least amount of material is referred to as ________.
Smallest
LMC
MMC
Actual size
Architectural drawings used to construct a house are often plotted with a scale of ¼ = 1'-0. What scale is this?
Quarter
Half
Full
Double
Spur gear design normally begins with selecting this:
Rack size
Tooth size
Gear size
Pitch diameter
This is used to indicate that a surface is to be machined:
Finish mark
Machining mark
Roughness indicator
Coordinate mark
This type of projection is when projectors are parallel to each other, but is at an angle other than 90 degrees to the plane of projection:
Oblique projection
Perpendicular projection
Aesthetic projection
Angular projection
Oblique drawings are dimensioned in a similar fashion as these types of drawings:
Orthographic
Isometric
Angular
Parallel
By using a ________ section of a cylindrical mechanical part the drafter should be able to show only one view of the part.
Half
Whole
Revolved
Broken out
In this type of projection, each of the axes has different ratios of foreshortening:
Isometric
Dimetric
Trimetric
Parallel
EDM is the acronym for:
Enterprise data management
Engineering drawing management
Enterprise drawing manipulation
Engineering data manipulation
These are accurately drawn maps of cities and towns showing property lines and other features that control property ownership:
Monument maps
Cadastral maps
City maps
Topographic maps
When filling an area with a hatch pattern in Auto-CAD the drafter needs to be able to ________.
See the entire bounding area to hatch
Set Ortho on
Turn ISO grid off
Set the layer to Defpoints
Which of the following is one of the basic types of welded joints:
T-joint
Rear joint
Angle joint
Groove joint
On a floor plan the dashed line that appears approximately 24 outside the exterior wall represents the __________.
Sidewalk
Roof overhang
Plumbing drain lines
None of the above
This is formed where three or more surfaces intersect:
Oblique
Line
Edge
Vertex
In working drawings, these show all necessary information not given directly on the drawing with its dimensions and notes:
Document strips
Portable documents
Formatting forms
Title and record strips
An advantage of this type of view is that each view shows the object all the way through as if it were transparent:
Planar
Horizontal
Auxiliary
Orthographic
This process recognizes the inherent interrelationships between design and manufacturing:
Design for manufacture
Design for manufacture and assembly
Design for concurrent engineering
Design for assembly
A fillet is a rounded surface on the ________ corner of a part.
Inside
Outside
Radial
Isoplane
A partial auxiliary view usually shows only features on the ________ of the inclined line and not any projection of other planes.
Hidden lines
Plane
Center lines
None of the above
Drafters should use a ________ in a section view of a mechanical part that includes the cylindrical view of a threaded hole.
Center line
Hatch line
Poly line
Dimension line
Most architectural drawings produced for field use by building contractors are printed on architectural D size paper which measures ________.
24 × 36
18 × 24
11 × 17
34 × 22
If designs require changes, they should be documented with:
Development plans
Product proposals
Document reviews
Engineering change orders
A full scale technical drawing will have a scale factor of ________.
1 : 1
1 : 2
2 : 1
1 : 4
This is a systematic approach that integrates the design and manufacture of products with the goal of optimizing the process:
Traditional engineering design
The manufacturing process
Concurrent design
Design for recycling