Related Questions
What is the correct answer?
4
This type of thread is a thread on the inside of a member:
What is the correct answer?
4
The most common geometric form used in gears today is this:
What is the correct answer?
4
This type of solid has a polygon for a base and triangular lateral faces that intersect at a vertex:
What is the correct answer?
4
The condition of a part when it contains the least amount of material is referred to as ________.
What is the correct answer?
4
The offset distance for the width (front to back) distance of the auxiliary view is the same distance of the ________ in the top view.
What is the correct answer?
4
PDM is the acronym for:
A. Project drawing management
B. Product drawing manipulation
C. Product data management
D. Project data manipulation
What is the correct answer?
4
Referring to the fractional inches to decimal inches to millimetre conversion chart on page 55 what is the equivalent mm measurement of 3/16 inch.
What is the correct answer?
4
When using versions of Auto-CAD prior to Release 2006 it may be necessary to ________ a block in order to edit it.
What is the correct answer?
4
The ________ dimension tool will place the length of an angled line.
What is the correct answer?
4
The building construction industry relies on sets of ________ drawings to construct homes and commercial buildings.
What is the correct answer?
4
Drawings created with commercial software are typically saved as:
What is the correct answer?
4
Elevation drawings will include information about ________.
What is the correct answer?
4
A projection weld is a type of:
What is the correct answer?
4
In an exploded assembly drawing it is customary for the drafter to use a ________ line to illustrate how parts fit together.
What is the correct answer?
4
This type of drawing shows two lines representing the pipe diameter:
What is the correct answer?
4
Placement of dimensions on a drawing is controlled by ________.
C. Corporate drafting standards
What is the correct answer?
4
Some traditional board drafters preferred the drafting machine over the parallel straight edge because it could be used without the need for________.
What is the correct answer?
4
In order to set drawing limits for a C size architectural drawing the drafter should set the limits to ________.
What is the correct answer?
4
This is an angled surface used on cylinders to make them easier to handle:
What is the correct answer?
4
These breaks are used to shorten the view of an object:
What is the correct answer?
4
Circular shapes appear in this fashion when viewed at an angle other than 90 degrees:
What is the correct answer?
4
The title block used on working drawings should include the __________.
What is the correct answer?
4
This type of structural steel drawing shows all dimensions necessary for fabrication:
What is the correct answer?
4
This should show what changes were made, when, and by whom:
What is the correct answer?
4
This is a curve showing the displacement of the follower as ordinates on a base line that represents one revolution of the cam:
What is the correct answer?
4
This is the intersection of the ground plane with the picture plane:
What is the correct answer?
4
When designing a home for a client, one of the most important predesign considerations that an architect needs to address is ________.
A. How much money the client is willing to spend
B. The site on which the house is to sit
C. The nearest grocery store
D. Whether or not there is a curb and gutter system
What is the correct answer?
4
When creating an isometric drawing in Auto-CAD the drafter can utilize the Dynamic Input and Polar Coordinate system to place both vertical and horizontal lines. A line created from one point 3 inches at 180 degrees would be a ________ line.
What is the correct answer?
4
In oblique projection, important shapes should be in this position relative to the viewing plane:
What is the correct answer?
4
Using the Relative Polar Coordinate System to add a 3 inch line that is 45 degrees from the end point of the line created above the drafter would ________.
B. Type 3 back slash and enter
C. Type 3 forward slash and enter
D. Type 3 and try to use the Dynamic Input readout to find the end point