Related Questions
What is the correct answer?
4
On typical electronic diagrams, these items need not be shown unless they are needed for clarification:
What is the correct answer?
4
The ________ is a standard element of a section view in a technical drawing.
C. Material hatch pattern
What is the correct answer?
4
In order to set drawing limits for a C size architectural drawing the drafter should set the limits to ________.
What is the correct answer?
4
Placement of dimensions on a drawing is controlled by ________.
C. Corporate drafting standards
What is the correct answer?
4
There are two main types of projection:
A. Parallel and Orthographic
B. Station-point and Perspective
C. Parallel and Convergent
D. Perspective and Parallel
What is the correct answer?
4
In multi-view drawing it is common practice to include three views, the front, the top and the right side. If no dimensions are required on the right side view the drafter can ________.
C. Use the left view instead
What is the correct answer?
4
If designs require changes, they should be documented with:
D. Engineering change orders
What is the correct answer?
4
This is the total amount that the feature on the actual part is allowed to vary from what is specified by the dimension:
What is the correct answer?
4
This is the plane upon which the top view is projected:
What is the correct answer?
4
Dimension text is generally placed above the ________ line.
What is the correct answer?
4
This is the measured size of a finished part:
What is the correct answer?
4
When using the direct entry method to create a horizontal line exactly three inches long the drafter should ________ first.
A. Pull the line from away from the starting point very carefully
B. Insure that Ortho is on
C. Enter 3 for the length of the line
D. Read the coordinate position on the Dynamic Readout
What is the correct answer?
4
Students can complete an associate's degree in drafting which normally takes about ________ years to complete.
What is the correct answer?
4
When using versions of Auto-CAD prior to Release 2006 it may be necessary to ________ a block in order to edit it.
What is the correct answer?
4
These are special installations of stone or concrete marking the locations of points accurately determined by precise surveying:
What is the correct answer?
4
Once the architect has finalized the house plans with the client any changes to the design requested by the client will require a ________.
C. Whole new set of drawings
What is the correct answer?
4
Before starting an isometric drawing in Auto-CAD the drafter needs to ________.
A. Set the grid to isometric
B. Set the current layer to Defpoints
What is the correct answer?
4
This type of circuit is a semiconductor wafer or chip:
What is the correct answer?
4
This is a conical-shaped recess around a hole, often used to receive a tapered screw head:
What is the correct answer?
4
Approximately this much of the cost of product development and manufacture is determined at the design stage:
What is the correct answer?
4
An architect often relies on a ________ to complete the set of technical drawings used in the design of an office building.
D. Construction superintendent
What is the correct answer?
4
In U.S. structural and architectural drafting, all dimensions of this length are usually expressed in feet and inches:
What is the correct answer?
4
The foundation contractor will work with the following architectural plans.
What is the correct answer?
4
In oblique projection, important shapes should be in this position relative to the viewing plane:
What is the correct answer?
4
This process recognizes the inherent interrelationships between design and manufacturing:
A. Design for manufacture
B. Design for manufacture and assembly
C. Design for concurrent engineering
What is the correct answer?
4
By using a ________ section of a cylindrical mechanical part the drafter should be able to show only one view of the part.
What is the correct answer?
4
This allows the performance of structures to be analyzed and tested efficiently, accurately, and quickly:
A. Computer-aided manufacturing
C. Computer-aided engineering
D. Computer-aided prototyping
What is the correct answer?
4
Acceptable parts must not extend beyond this:
What is the correct answer?
4
This is the theoretically exact size from which limits of size are determined:
What is the correct answer?
4
In the section view, the areas that would have been in actual contact with the cutting plane are shown with: