Related Questions
What is the correct answer?
4
The design of pin of a rocker arm of an I.C. engine is based on
What is the correct answer?
4
A shaft is subjected to fluctuating loads for which the normal torque (T) and bending moment (M) are 1000 N-m and 500 N-m respectively. If the combined shock and fatigue factor for bending is 1.5 and combined shock and fatigue factor for torsion is 2, then the equivalent twisting moment for the shaft is
What is the correct answer?
4
The included angle in unified of American National threads is
What is the correct answer?
4
A localised compressive stress at the area of contact between two members is known as
What is the correct answer?
4
When a nut is tightened by placing a washer below it, the bolt will be subjected to following type of loads
What is the correct answer?
4
Stress concentration is caused due to
A. Variation in properties of material from point to point in a member
B. Pitting at points or areas at which loads on a member are applied
C. Abrupt change of section
What is the correct answer?
4
In testing a material for endurance strength, it is subjected to
D. Completely reversed load
What is the correct answer?
4
A type of brake commonly used in motor cars is a
D. Internal expanding brake
What is the correct answer?
4
A steel containing upto 0.15% carbon is known as
What is the correct answer?
4
In helical gears, the distance parallel to the axis, between similar faces of adjacent teeth, is called
What is the correct answer?
4
The gears are termed as medium velocity gears, if their peripheral velocity is
What is the correct answer?
4
The centre to centre distance between two consecutive rivets in a row, is called
What is the correct answer?
4
A connecting rod should be
A. Strong in buckling about X-axis
B. Strong in buckling about Y-axis
C. Equally strong in buckling about X-axis and Y-axis
What is the correct answer?
4
The washer is generally specified by its
What is the correct answer?
4
Buttress threads are usually found on
C. Spindles of bench vices
D. Railway carriage couplings
What is the correct answer?
4
The power transmitted by the belt drive can be increased by
A. Increasing the initial tension in the belt
B. Dressing the belt to increase the coefficient of friction
C. Increasing wrap angle by using idler pulley
D. All of the above methods
What is the correct answer?
4
A screw is said to be over hauling screw, if its efficiency is
What is the correct answer?
4
The piston rod of a steam engine is usually connected to the crosshead by means of
What is the correct answer?
4
The pipe joint mostly used for pipes carrying water at low pressures is
D. Spigot and socket joint
What is the correct answer?
4
The ball bearings are provided with a cage
B. To facilitate slipping of balls
C. To prevent the lubricant from flowing out
D. To maintain the balls at a fixed distance apart
What is the correct answer?
4
A metal pipe of 1 m diameter contains a fluid having a pressure of 1 N/mm². If the permissible tensile stress in the metal is 20 N/mm², then the thickness of the metal required for making the pipe will be
What is the correct answer?
4
When two nonintersecting and non-coplanar shafts are connected by gears, the arrangement is known as
What is the correct answer?
4
According to I.B.R., when the thickness of the boiler shell (t) is less than 8 mm, then the diameter of the rivet hole (d) is obtained by
A. Equating tearing resistance of the plate to the shearing resistance of the rivets
B. Equating tearing resistance of the plate to the crushing resistance of the rivets
C. Equating shearing resistance to the crushing resistance of the rivets
What is the correct answer?
4
A special case of ductility which permits materials to be rolled or hammered into thin sheets, is called
What is the correct answer?
4
In helical gears, the distance between similar faces of adjacent teeth along a helix on the pitch cylinders normal to the teeth, is called
What is the correct answer?
4
For hardening alloy steels and high speed steels, they are heated to
What is the correct answer?
4
When an open coiled helical compression spring is subjected to an axial compressive load, the maximum shear stress induced in the wire is (where D = Mean diameter of the spring coil, d = Diameter of the spring wire, K = Wahl's stress factor, and W = Axial compressive load on the spring)
What is the correct answer?
4
The static tooth load should be __________ the dynamic load.
What is the correct answer?
4
According to I.B.R., the efficiency of a triple riveted butt joint with double straps of unequal width (5 rivets per pitch length) should be
What is the correct answer?
4
The size of a cam depends upon