The ___________ converts an ISDN four-wire connection to a two-wire connection.

Question

The ___________ converts an ISDN four-wire connection to a two-wire connection.

A. NT5

B. NP1

C. NT1

D. TN1

Correct Answer :

C. NT1

Share this question with your friends

Show all WAN MCQ

Comment

Private addressing is defined in RFC ______.

A. 1920

B. 1934

C. 1818

D. 1918

Discuss this answer

If you wanted a list of parameters for the show command, you would type ________.

A. LOOK

B. VIEW

C. SHOW

Discuss this answer

RIP has a maximum hop count of ____________ hops.

A. 10

B. 15

C. 16

D. 100

Discuss this answer

_________ describe(s) users working from home.

A. SOHO

Discuss this answer

The _________ is your network equipment, which includes the DCE (e.g., a modem) and the DTE (e.g., a router).

D. CPE

Discuss this answer

Which router command would you use to view the configuration register value?

Discuss this answer

A Class A address has _________ host bits.

A. 8

B. 16

C. 20

D. 24

Discuss this answer

On the 1900 switch, how do you enter User EXEC mode?

Discuss this answer

You are given a Class C network, 192.168.1.0/24. You need one network with 120 hosts
and two networks with 60 hosts. How many subnet masks do you need?

A. 1

B. 2

C. 3

D. 4

Discuss this answer

Which command is used to define the local addresses that are statically translated to global addresses?

Discuss this answer

When connecting a router to a PC, use a __________ cable.

Discuss this answer

Which types of memory do not maintain their contents during a power-off state?

A. NVRAM

B. ROM

C. RAM

D. Flash

Discuss this answer

Which controller command specifies how ones and zeros are represented on a digital circuit?

Discuss this answer

When you have configured PPP on an interface and use the show interfaces command, what state indicates the successful negotiation of a network layer protocol?

A. ACK

C. CLOSED

D. OPEN

Discuss this answer

An OSPF's router ID is based on __________.

Discuss this answer

OSPF uses __________ as a metric.

B. Delay

C. Cost

Discuss this answer

Which Frame Relay command is used to manually resolve addresses?

Discuss this answer

Which of the following is a private address?

Discuss this answer

A ___________ is basically all of the components, hardware and software, involved
in connecting computers across small and large distances.

A. LAN

B. WAN

D. SAN

Discuss this answer

Which of the following is a Network layer protocol for the TCP/IP protocol stack?

A. TCP

B. UDP

C. ICMP

Discuss this answer

When connecting a switch to a router, use a ___________ cable.

Discuss this answer

The OSPF process ID is __________.

Discuss this answer

You are given a MAC address of 01A2.0482.FE12. What is the OUI value in binary?

Discuss this answer

PPP can do all of the following except ___________.

Discuss this answer

The switch port that is chosen to forward traffic for a segment is called a __________.

Discuss this answer

OSPF hellos are sent every __________ seconds on a multi-access medium.

A. 5

B. 10

C. 15

D. 40

Discuss this answer

Which router command would you use to test only layer-3 connectivity?

A. telnet

Discuss this answer

Which of the following is true concerning bridges?

Discuss this answer

During the learning function, the switch places addresses and ports in a(n) _________ table.

C. CAM

D. memory

Discuss this answer

What router command saves the active configuration to NVRAM?

Discuss this answer

Answer 1

B. Branch office

Answer 2

C. Regional office

Answer 3

D. Corporate office

Answer 4

A. Demarcation point

Answer 5

B. Carrier switch

Answer 6

C. Local loop

Answer 7

A. show register

Answer 8

B. show interfaces

Answer 9

C. show configuration

Answer 10

D. show version

Answer 11

A. It comes up by default.

Answer 12

B. Enter the letter U in the menu.

Answer 13

C. Enter the letter K in the menu.

Answer 14

D. Enter the letter C in the menu.

Answer 15

A. ip nat inside source static

Answer 16

B. ip nat inside

Answer 17

C. ip nat inside source list

Answer 18

D. ip nat pool

Answer 19

A. Crossover

Answer 20

B. Straight-through

Answer 21

C. Rollover

Answer 22

A. framing

Answer 23

B. linecode

Answer 24

C. clock source

Answer 25

D. interface

Answer 26

B. CHALLENGE

Answer 27

A. The lowest IP address on its loopback interface, if configured, or the lowest IP address onits active interfaces

Answer 28

B. The highest IP address on its loopback interface, if configured, or the highest IP address on its active interfaces

Answer 29

C. The highest IP address on its active interfaces, if configured, or the highest IP address on its loopback interfaces

Answer 30

D. The lowest IP address on its active interfaces, if configured, or the lowest IP address on its loopback interfaces

Answer 31

A. Bandwidth

Answer 32

D. Hop count

Answer 33

A. frame-relay interface-dlci

Answer 34

B. frame-relay map

Answer 35

C. frame-relay resolve

Answer 36

D. frame-relay lmi-type

Answer 37

A. 192.169.7.17

Answer 38

B. 172.32.28.39

Answer 39

C. 10.1.256.8

Answer 40

D. 172.16.255.89

Answer 41

C. Network

Answer 42

D. None of these

Answer 43

A. Crossover

Answer 44

B. Straight-through

Answer 45

C. Rollover

Answer 46

A. Locally significant and is the router ID

Answer 47

B. Globally significant and must be configured on every router

Answer 48

C. Locally significant

Answer 49

D. OSPF doesn't use a process ID, but an AS number

Answer 50

A. 00011011.10100010.00000100

Answer 51

B. 00000000.00000001.00000100

Answer 52

C. 00000001.10100010.00000100

Answer 53

D. 00000001.10100001.00000010

Answer 54

A. Authentication

Answer 55

B. Compression

Answer 56

C. Quality of Service

Answer 57

D. None of these

Answer 58

A. Root port

Answer 59

B. Alternate port

Answer 60

C. Backup port

Answer 61

D. Designated port

Answer 62

B. show cdp traffic

Answer 63

C. show interfaces

Answer 64

D. traceroute

Answer 65

A. They switch frames in hardware.

Answer 66

B. They support half- and full-duplexing.

Answer 67

C. They support one collision domain for the entire bridge.

Answer 68

D. They do only store-and-forward switching.

Answer 69

A. IP address

Answer 70

B. learning

Answer 71

A. copy nvram startup-config

Answer 72

B. copy startup-config running-config

Answer 73

C. copy running-config nvram

Answer 74

D. copy running-config startup-config

The ___________ converts an ISDN four-wire connection to a two-wire connection.

Correct Answer :

Show all WAN MCQ

Related Questions

Private addressing is defined in RFC ______.

If you wanted a list of parameters for the show command, you would type ________.

RIP has a maximum hop count of ____________ hops.

_________ describe(s) users working from home.

The _________ is your network equipment, which includes the DCE (e.g., a modem) and the DTE (e.g., a router).

Which router command would you use to view the configuration register value?

A Class A address has _________ host bits.

On the 1900 switch, how do you enter User EXEC mode?

You are given a Class C network, 192.168.1.0/24. You need one network with 120 hosts
and two networks with 60 hosts. How many subnet masks do you need?

Which command is used to define the local addresses that are statically translated to global addresses?

When connecting a router to a PC, use a __________ cable.

Which types of memory do not maintain their contents during a power-off state?

Which controller command specifies how ones and zeros are represented on a digital circuit?

When you have configured PPP on an interface and use the show interfaces command, what state indicates the successful negotiation of a network layer protocol?

An OSPF's router ID is based on __________.

OSPF uses __________ as a metric.

Which Frame Relay command is used to manually resolve addresses?

Which of the following is a private address?

A ___________ is basically all of the components, hardware and software, involved
in connecting computers across small and large distances.

Which of the following is a Network layer protocol for the TCP/IP protocol stack?

When connecting a switch to a router, use a ___________ cable.

The OSPF process ID is __________.

You are given a MAC address of 01A2.0482.FE12. What is the OUI value in binary?

PPP can do all of the following except ___________.

The switch port that is chosen to forward traffic for a segment is called a __________.

OSPF hellos are sent every __________ seconds on a multi-access medium.

Which router command would you use to test only layer-3 connectivity?

Which of the following is true concerning bridges?

During the learning function, the switch places addresses and ports in a(n) _________ table.

What router command saves the active configuration to NVRAM?

Also checkout

The ___________ converts an ISDN four-wire connection to a two-wire connection.

Correct Answer :

Show all WAN MCQ

Related Questions

Private addressing is defined in RFC ______.

If you wanted a list of parameters for the show command, you would type ________.

RIP has a maximum hop count of ____________ hops.

_________ describe(s) users working from home.

The _________ is your network equipment, which includes the DCE (e.g., a modem) and the DTE (e.g., a router).

Which router command would you use to view the configuration register value?

A Class A address has _________ host bits.

On the 1900 switch, how do you enter User EXEC mode?

You are given a Class C network, 192.168.1.0/24. You need one network with 120 hostsand two networks with 60 hosts. How many subnet masks do you need?

Which command is used to define the local addresses that are statically translated to global addresses?

When connecting a router to a PC, use a __________ cable.

Which types of memory do not maintain their contents during a power-off state?

Which controller command specifies how ones and zeros are represented on a digital circuit?

When you have configured PPP on an interface and use the show interfaces command, what state indicates the successful negotiation of a network layer protocol?

An OSPF's router ID is based on __________.

OSPF uses __________ as a metric.

Which Frame Relay command is used to manually resolve addresses?

Which of the following is a private address?

A ___________ is basically all of the components, hardware and software, involvedin connecting computers across small and large distances.

Which of the following is a Network layer protocol for the TCP/IP protocol stack?

When connecting a switch to a router, use a ___________ cable.

The OSPF process ID is __________.

You are given a MAC address of 01A2.0482.FE12. What is the OUI value in binary?

PPP can do all of the following except ___________.

The switch port that is chosen to forward traffic for a segment is called a __________.

OSPF hellos are sent every __________ seconds on a multi-access medium.

Which router command would you use to test only layer-3 connectivity?

Which of the following is true concerning bridges?

During the learning function, the switch places addresses and ports in a(n) _________ table.

What router command saves the active configuration to NVRAM?

Also checkout

You are given a Class C network, 192.168.1.0/24. You need one network with 120 hosts
and two networks with 60 hosts. How many subnet masks do you need?

A ___________ is basically all of the components, hardware and software, involved
in connecting computers across small and large distances.