Home
Current Affairs January 2024

What is the correct answer?

4

The crescent shaped cavity on the piston head top surface is called as

A. Piston oil hole

B. Snap ring

C. Valve recess

D. Valve clearance

Correct Answer :

C. Valve recess


Related Questions

What is the correct answer?

4

The fuel pump of a programmed fuel injection (PFI) system operate for two seconds when the ignition is turned to the start position to

A. Enable the pump's fault diagnosis function to operate

B. Warm up and lubricate the pump

C. Supplies a large amount of fuel and thereby creates a choke effect

D. Pressurise the fuel system before the engine is started

What is the correct answer?

4

The natural gas is compressed in a CNG cylinder at a pressure of

A. 200 bar

B. 220 bar

C. 250 bar

D. 300 bar

What is the correct answer?

4

The main function of the brake fluid is

A. Lubrication

B. Power transmission

C. Cooling

D. None of these

What is the correct answer?

4

In a four wheel drive (4WD), the numbers of gear boxes are

A. 1

B. 2

C. 3

D. 4

What is the correct answer?

4

Instead of valves, the ports are used in case of

A. Four stroke I.C. engines

B. Two stroke I.C. engines

C. V6 engines

D. None of these

What is the correct answer?

4

The lubrication oil flow in an engine is in the order as

A. Oil strainer, oil pump, relief valve, oil filter, cylinder block, cylinder head and oil pan

B. Oil pump, oil strainer, relief valve, oil filter, cylinder block, cylinder head and oil pan

C. Oil strainer, oil filter, relief valve, oil pump, cylinder block, cylinder head and oil pan

D. Oil strainer, oil pump, relief valve, oil filter, cylinder head, cylinder block and oil pan

What is the correct answer?

4

The parking brake generally acts on

A. Front wheels

B. Rear wheels

C. Front and rear wheels

D. Propeller shaft

What is the correct answer?

4

In automobiles G.V.W. refers to

A. Gross vehicle width

B. Gross vehicle weight

C. Gross vehicle wheel base

D. Gross vehicle wheel track

What is the correct answer?

4

The ball joints are used on the tie rod ends, because they

A. Reduce the amount of noise generated

B. Reduce the amount of sliding resistance

C. Can deal with movement of the suspension both vertically and in other directions

D. Improve the force transmission speed

What is the correct answer?

4

The component of the oil filter that prevents the passage of metal particles and sludge is

A. Element

B. Relief valve

C. Check valve

D. Case

What is the correct answer?

4

The ease with which petrol vaporizes is called its

A. Oxidation

B. Octane number

C. Volatility

D. Cetane number

What is the correct answer?

4

The difference between DOT 3 and DOT 4 brake fluids is

A. DOT 4 fluids have a higher boiling point than DOT 3 fluid

B. DOT 4 fluids have a lower boiling point than DOT 3 fluid

C. DOT 3 and DOT 4 fluids have the same boiling point, but DOT 4 fluid has a longer service life

D. DOT 4 fluid is more resistant to freezing than DOT 3 fluid

What is the correct answer?

4

Valve overlap is the number of degrees of camshaft rotation during which

A. Both valves are closed

B. Both valves are open

C. Both 'A' and 'B'

D. None of these

What is the correct answer?

4

In radial tyres

A. One ply layer runs diagonally one way and another layer runs diagonally the other way

B. All plies run parallel to one another and vertical to tyre bead

C. Inner tubes are always used

D. None of these

What is the correct answer?

4

The negative plates of a lead acid battery has

A. Lead peroxide (PbO₂)

B. Spongy lead (Pb)

C. Lead sulphate (PbSO₄)

D. Sulphuric acid (H₂SO₄)

What is the correct answer?

4

If the air-fuel mixture in a spark ignition engine is too rich, then airfuel ratio is about

A. 17 : 1

B. 15 : 1

C. 13 : 1

D. 10 : 1

What is the correct answer?

4

Incorrect steering axis inclination (S.A.I.) causes

A. Tendency to assume toe-out orientation

B. Generation of a braking effect at tight corners

C. Poor recovery of the steering wheel after making a turn

D. The vehicle to pull to the side of lesser inclination

What is the correct answer?

4

During braking, the brake shoe is moved outward to force the lining against the

A. Wheel piston or cylinder

B. Anchor pin

C. Brake drum

D. Wheel rim or axle

What is the correct answer?

4

The main function of a resonator is that it

A. Regulates the intake air flow rate

B. Reduces the intake air noise

C. Enhances intake efficiency

D. Regulates the intake air temperature

What is the correct answer?

4

In bias ply tyres

A. All plies run parallel to one another

B. Belts of steel mesh are used in the tyres

C. One ply layer runs diagonally one way and another layer runs diagonally the other way

D. All of the above

What is the correct answer?

4

In a petrol engine, the high voltage for spark plug is in the order of

A. 1000 volts

B. 2000 volts

C. 11 kilovolts

D. 22 kilovolts

What is the correct answer?

4

If a tyre is designated as 175/65 R-14 82-S, then the aspect ratio for the tyre is

A. 175

B. 65

C. 14

D. 82

What is the correct answer?

4

The crankcase dilution means

A. Dilution of fuel in the crankcase

B. Dilution of oil by water in the crankcase

C. Dilution of lubrication oil by fuel in the crankcase

D. Dilution of mixture passing through crankcase in two stroke engines

What is the correct answer?

4

The function of antilock brake system (ABS) is that is

A. Reduces the stopping distance

B. Minimises the brake fade

C. Maintains directional control during braking by preventing the wheels from locking

D. Prevents nose dives during braking and thereby postpones locking of the wheels

What is the correct answer?

4

Free pedal play in car clutches is about

A. 15 mm

B. 25 mm

C. 40mm

D. 60 mm

What is the correct answer?

4

The size of engine cylinder is referred in terms of its

A. Diameter and bore

B. Displacement and efficiency

C. Bore and stroke

D. Bore and length

What is the correct answer?

4

Bead wires are made of

A. Steel

B. Copper

C. Zinc

D. Aluminium

What is the correct answer?

4

When the top of the wheel is tilted outward, then it is called

A. Positive camber

B. Negative camber

C. Positive caster

D. Negative caster

What is the correct answer?

4

The diagram which shows the correct crank positions corresponding to the opening and closing of the valves, is known as

A. Indicator diagram

B. Axial force diagram

C. Valve timing diagram

D. None of these

What is the correct answer?

4

The auto ignition in a spark ignition engine means

A. Automatic ignition of the charge at the end of compression

B. Ignition induced by the passage of a spark

C. Ignition of the charge before the passage of flame front

D. Ignition induced to supplement the process of normal combustion