Related Questions
What is the correct answer?
4
Pick out the correct combination about the role of various additives used in polymers.
A. Plasticiser: increases the polymer strength
B. Heat stabiliser: increases the maximum service temperature
C. Fillers: Does not affect the property of polymer but increases its weight
D. Lubricants: increases the flexibility of polymers
What is the correct answer?
4
If a solid is compressed adiabatically in its elastic range, its __________ remains constant
What is the correct answer?
4
The two elements required to form substitutional solid solution should not have
A. Same crystalline structure
C. Widely differing electronegativity
What is the correct answer?
4
Pick out the correct statement
A. Jet engine can work, where there is no atmosphere
B. Rocket engines cannot work, where there is no atmosphere
C. Rocket engines carry oxygen required for the combustion in the form of oxidiser
D. Jet engines also carry oxidiser
What is the correct answer?
4
Use of water as a manometric liquid suffers from the disadvantage of its
What is the correct answer?
4
Pressure exerted by a liquid depends upon its
What is the correct answer?
4
What is the critical radius of insulation (cms) for a metallic cylinder, if the convective heat transfer co-efficient with the ambient atmosphere is 5 W/m2. °K? Thermal conductivity of metal and insulation material are 40 and 0.1 W/m.°K respectively.
What is the correct answer?
4
In case of condensers & evaporators operating under given terminal conditions, LMTD (logarithmic mean temperature difference) for counter flow as compared to that for parallel flow is
What is the correct answer?
4
Maximum change in the hardness of martensite occurs in the carbon content range of __________ percent in steel.
What is the correct answer?
4
Wohler test is a destructive test to find out the __________ strength of a prepared metal specimen.
What is the correct answer?
4
Faraday's law of electrolysis is related to the
B. Atomic number of the cation
C. Equivalent mass of the electrolyte
What is the correct answer?
4
In an eutectic system, two elements are completely
A. Soluble in solid state
B. Insoluble in liquid state
C. Insoluble in both solid & liquid state
D. Soluble in liquid state
What is the correct answer?
4
Stainless steel is welded with difficulty because of
A. Its high melting temperature
D. Chromium carbide formation
What is the correct answer?
4
Most of the phosphorous present in the blast furnace burden enters into
What is the correct answer?
4
The wet bulb temperature is lower in dry air than in wet air at the same temperature. A dry bulb thermometer registers a higher temperature than a wet bulb thermometer except at __________ percent relative humidity.
What is the correct answer?
4
To counteract the bad effects of strain hardening on a cold formed part, it must be
What is the correct answer?
4
Nusselt number/Biot number varies
A. Inversely with thermal conductivity
B. Directly with heat transfer co-efficient
C. Directly with thermal conductivity
D. Inversely with the dimension of the solid
What is the correct answer?
4
The starting of a car takes time in winter, because the
A. Octane number of fuel is decreased
B. Fuel supply for ignition is not sufficient
C. Vaporisation of the fuel is decreased
D. Pour point of fuel decreases
What is the correct answer?
4
Heat required to raise the temperature of a body by 1 °C is called its
B. Specific heat capacity
What is the correct answer?
4
Potable water means the water used for
D. Evaporation to produce steam
What is the correct answer?
4
Which of the following is preferred for riveting?
What is the correct answer?
4
Coating thickness in case of galvanising of steel sheet generally corresponds to the deposition of __________ gms of zinc per of steel strip.
What is the correct answer?
4
Between 230 and 370°C, blue brittleness is caused in mild steel because of the
A. Immobility of dislocation
C. Increase in Young's modulus
What is the correct answer?
4
The phenomenon occurring during explosion of a hydrogen bomb is
C. A combination of both nuclear fission & fusion
What is the correct answer?
4
The bank of tubes located at the back of the domestic refrigerators are the __________ tubes.
What is the correct answer?
4
Which of the following is not used as a bearing material?
What is the correct answer?
4
Fatigue resistance of a material is measured by the
B. Ultimate tensile strength
What is the correct answer?
4
The softness or hardness of a grinding wheel depends upon the type & amount of bonding material used. For general purpose cutter grinding __________ grinding wheel is normally used.
What is the correct answer?
4
On decreasing the grain size of a polycrystalline material, the property most likely to deteriorate is
What is the correct answer?
4
Two wires of the same radius & material having length in the ratio of 1 : 2 are stretched by the same force. The strain produced in the two wires will be in the ratio of