Related Questions
What is the correct answer?
4
Out of the following, the best material capable of withstanding shock & vibration without the danger of cracking is
What is the correct answer?
4
Nusselt number/Biot number varies
A. Inversely with thermal conductivity
B. Directly with heat transfer co-efficient
C. Directly with thermal conductivity
D. Inversely with the dimension of the solid
What is the correct answer?
4
Which of the following is not a principal alloying element for the structural steel?
What is the correct answer?
4
The most suitable material of construction for a sewer to carry sewage under high pressure is
What is the correct answer?
4
Water-tube boiler is the one, in which
A. Water passes through tubes and flue gases around it
B. Tube carrying hot flue gases are immersed in a pool of water
C. Tubes are placed in vertical position
What is the correct answer?
4
More than 95% of __________ is present in corundum.
What is the correct answer?
4
Air-petrol ratio for maximum power generation in spark ignition engine is about
What is the correct answer?
4
Which of the following metals is not subjected to electrolytic refining/purification?
What is the correct answer?
4
What is the critical radius of insulation (cms) for a metallic cylinder, if the convective heat transfer co-efficient with the ambient atmosphere is 5 W/m2. °K? Thermal conductivity of metal and insulation material are 40 and 0.1 W/m.°K respectively.
What is the correct answer?
4
The size of the tetrahedral void in the closest packing of atoms is __________ that of the octahedral void.
D. Either (A), (B) or (C); depends on the size of atom
What is the correct answer?
4
The surface tension of a liquid, at critical temperature is
D. Same as that at any other temperature
What is the correct answer?
4
Dew point temperature always gives an indication of the __________ of the moist air.
What is the correct answer?
4
Fatigue limit improvement by over stressing the metal by successively increasing the load is called coaxing. In fatigue failure, the material fails
C. Below the elastic limit
What is the correct answer?
4
Temperature of hot gases flowing in a pipe is measured by a thermocouple inserted in the thermal well. The thermal well made of __________ will facilitate the most accurate measurement of the temperature.
What is the correct answer?
4
A fluid is termed as the Newtonian fluid, when the shear stress is __________ the velocity gradient.
B. Inversely proportional to
C. Directly proportional to
What is the correct answer?
4
Which of the following is a boiler accessory
i.e., not a boiler mounting?
What is the correct answer?
4
Lap joints are preferred over butt joints in soldering/brazing, because these joints are
A. Weaker in tension but stronger in shear
B. Weaker in shear but stronger in tension
C. Stronger in both shear and tension
D. The lap joints are easily made
What is the correct answer?
4
Yield strength of a polycrystalline metal with an average grain size d, is proportional to
What is the correct answer?
4
Steels with high carbon equivalent have poor Weldability, because in these steels during welding
A. Carbon and other alloying elements get oxidised from the weld pool
B. Excessive ferrite forms in the heat affected zone leading to poor toughness of the weld
C. Martensite forms in the heat affected zone leading to poor toughness/ductility of the weld
D. Segregation of carbon and other element occurs in the weld pool leading to poor properties of the weld
What is the correct answer?
4
Which of the following materials has the poorest electrical conductivity?
What is the correct answer?
4
Silicon in steel
A. Makes it usable in almost all magnetic circuits where alternating current is used
B. Increases its electrical resistivity and decreases the hysteresis loss
C. Is present upto 5% & 4% respectively when used in transformers & motor armatures
What is the correct answer?
4
For dynamic strain measurement, the Wheatstone bridge used is of __________ type.
A. Voltage sensitive null
B. Voltage sensitive deflected
C. Current sensitive deflected
What is the correct answer?
4
Speisses is a mixture of the following:
A. Arsenides of heavy metals
B. Antimonides of heavy metals
C. Arsenides & antimonides of heavy metals
D. Iron, cobalt and nickel
What is the correct answer?
4
Energy to be supplied to the radioactive nucleus for the emission of a neutron is __________ MeV.
What is the correct answer?
4
Unit of viscosity in CGS system is
What is the correct answer?
4
__________ is the process used for setting up compressive stresses in the surface of a metal to improve its fatigue strength.
What is the correct answer?
4
Which of the following fastening devices has its both ends threaded?
What is the correct answer?
4
Isotropic materials have the same __________ in all directions.
What is the correct answer?
4
The most detrimental impurity in high pressure boiler feed water is
What is the correct answer?
4
Cobalt - 60 is used as a source of __________ in medical therapy & industrial radiography.