Related Questions
What is the correct answer?
4
During the learning function, the switch places addresses and ports in a(n) _________ table.
What is the correct answer?
4
If the port status LED on a 2950 is ________, there is a physical layer connection problem.
A. Flashing green and amber
What is the correct answer?
4
OSPF hellos are sent every __________ seconds on a multi-access medium.
What is the correct answer?
4
_________ negotiates the data link and network layer protocols that will traverse a PPP connection.
What is the correct answer?
4
A _________ is a network that provides a secure connection from a company to other business partners.
What is the correct answer?
4
A ________ topology describes how devices communicate with each other.
What is the correct answer?
4
Which control sequence moves the cursor to the end of the line?
What is the correct answer?
4
___________ defines LAPD, which is responsible for the data-link layer connection between the router and the ISDN switch.
What is the correct answer?
4
RIP supports load balancing for up to __________ ___________ paths.
What is the correct answer?
4
What must you do to enable IP routing on your router? (Choose all of the correct answers.)
A. Enable the routing protocol.
B. Set clocking on all serial interfaces.
C. Assign IP addresses to your router's interfaces.
D. Assign the bandwidth parameter to your serial interfaces
What is the correct answer?
4
Which router command would you use to view the configuration register value?
What is the correct answer?
4
An OSPF's router ID is based on __________.
A. The lowest IP address on its loopback interface, if configured, or the lowest IP address onits active interfaces
B. The highest IP address on its loopback interface, if configured, or the highest IP address on its active interfaces
C. The highest IP address on its active interfaces, if configured, or the highest IP address on its loopback interfaces
D. The lowest IP address on its active interfaces, if configured, or the lowest IP address on its loopback interfaces
What is the correct answer?
4
Which router command creates a standard named ACL called test?
C. ip access-list standard test
D. access-list standard test
What is the correct answer?
4
You are given a MAC address of 01A2.0482.FE12. What is the OUI value in binary?
A. 00011011.10100010.00000100
B. 00000000.00000001.00000100
C. 00000001.10100010.00000100
D. 00000001.10100001.00000010
What is the correct answer?
4
Which command activates an IP ACL on a router's interface?
What is the correct answer?
4
VLSM allows you to summarize 192.168.2.0/24 and 192.168.3.0/24 as 192.168.2.0/25.
What is the correct answer?
4
You are given a class C network and you have four LAN segments with the following numbers of devices: 120, 60, and two with 30. What subnet mask values would you use to accommodate these segments?
What is the correct answer?
4
When choosing a dynamic routing protocol, which of the following should not be considered?
B. How routing information is shared
C. How routing information is processed
D. Number of PCs in the network
What is the correct answer?
4
You are given the following addressing information: 192.168.37.192/25. What type of address is this?
What is the correct answer?
4
Private addressing is defined in RFC ______.
What is the correct answer?
4
OSPF uses __________ as a metric.
What is the correct answer?
4
With a rollover cable, pin 7 on one end is mapped to pin ________ on the other end.
What is the correct answer?
4
IGRP generates an update every ___________ seconds.
What is the correct answer?
4
The slot number of a 1900's Fast Ethernet uplink ports is ________.
D. No slot number is used
What is the correct answer?
4
_________ describe(s) users that can connect to a network from any location.
What is the correct answer?
4
Which protocol supports VLSM?
What is the correct answer?
4
Which of the following trunking methods is/are proprietary to Cisco?
What is the correct answer?
4
Which of the following is true concerning ISL?
A. It is supported on both the 1900 and 2950 switches.
B. It adds a 26-byte trailer and 4-byte header.
C. Tagging is done in software.
D. The original Ethernet frame is not modified.
What is the correct answer?
4
Which 1900 command enables port security?
D. switchport port-security
What is the correct answer?
4
The default encapsulation on a synchronous serial interface is _________.