The dimension text size is determined by what the architect deems necessary in __________.
Model space
Paper space
The Finished plot
The PDF file
Correct Answer :
C. The Finished plot
Related Questions
The foundation contractor will work with the following architectural plans.
Foundation
Site plan
Floor plan
All of the above
Most architectural drawings produced for field use by building contractors are printed on architectural D size paper which measures ________.
24 × 36
18 × 24
11 × 17
34 × 22
To insure that everyone understands what the electrical symbols represent it is customary to include a ________ on the electrical sheet.
List
Part number
Electrical legend
Electrical layer
Two-point perspective is also known as:
Two-view perspective
Regular perspective
Parallel perspective
Angular perspective
The thread note for a typical bolt will include the ________.
Major diameter of the thread
Material
Center line
Offset distance
This is a thin solid line directing attention to a note or dimension and starting with an arrowhead or dot:
Dimension line
Extension line
Leader
Specification
When using versions of Auto-CAD prior to Release 2006 it may be necessary to ________ a block in order to edit it.
Copy
Explode
Offset
None of the above
One way to evenly space dimensions on a drawing is to use the ________.
Dimension Space tool
Linear tool
Continue tool
Baseline tool
A ________ is the person responsible for verifying that the drawings in a project set are free of mistakes.
Client
CAD trainee
Receptionist
Checker
Drawings created with commercial software are typically saved as:
Rapid prototypes
Electronic files
Draft drawings
Change orders
Elevation drawings will include information about ________.
Roof pitch
Siding
Window style
All of the above
Students can complete an associate's degree in drafting which normally takes about ________ years to complete.
One
Two
Three
Four
When setting up a mechanical drawing in Auto-CAD the drafter should set the units to ________.
Fractional
Decimal
Architectural
Metric
5.These items typically are not used in new designs, but are still common in high-power amplifiers:
Amplifier tubes
Electron tubes
Signal relays
Switches
A partial auxiliary view is used to show only the ________ in the auxiliary view.
Projected inclined plane
The projected top view
The projected side view
None of the above
In the mechanical design process the first step is to ________.
Brainstorm solutions
Prepare rough sketches
Prepare a budget
Identify the problem
This is a flat or rounded tab protruding from a surface, usually to provide a method for attachment:
Lug
Boss
Chamfer
Spotface
This is the measured size of a finished part:
Actual size
Dimensioned size
Production size
Basic size
This is a rounded exterior blend between surfaces:
Fillet
Round
Taper
Chamfer
In a CAD system, you can draw an ellipse by specifying these:
The bounding lines
The midpoint and end points
The center and major and minor axes
The center and radius
In order to convert fractional inches into decimal inches ________.
Look on a metric conversion chart
Divide the numerator (top number) by the denominator (bottom number)
Check the engineer's scale
All of the above
When dimensioning architectural drawings architects will utilize both ________ and ________ options.
Baseline and continuous
Baseline and linear
Quick dim and linear
Linear and continuous
In order to create an isometric circle to represent a hole through the top surface of a box, the drafter must insure that the correct iso-plane has been selected by scrolling through the iso-planes using the ________ key.
F1
F3
F5
F8
The text height for room names should be set to ________for a drawing that will be plotted to a scale of ¼ = 1'-0.
4
5
6
8
A round is a rounded surface on the ________ corner of a part.
Inside
Outside
Radial
Isoplane
This is the plane upon which the top view is projected:
Horizontal
Frontal
Profile
Base
Most architectural firms and mechanical design companies utilize different categories of blocks. These sets of blocks are usually housed in ________.
Block vaults
Block libraries
Block books
Block references
A typical set of mechanical working drawings includes ________.
Exploded assembly
Part details
Parts list
All of the above
This process recognizes the inherent interrelationships between design and manufacturing:
Design for manufacture
Design for manufacture and assembly
Design for concurrent engineering
Design for assembly
In the section view, the areas that would have been in actual contact with the cutting plane are shown with:
A cutting plane line
Section lining
Visible lines
Lines and arrows