Home
Current Affairs January 2024

What is the correct answer?

4

The draw of cotter should not be more than

A. 3 mm

B. 6 mm

C. 8 mm

D. 12 mm

Correct Answer :

A. 3 mm


Related Questions

What is the correct answer?

4

Spring stiffness is

A. Ratio of coil diameter to wire diameter

B. Load required to produce unit deflection

C. Its capability of storing energy

D. Its ability to absorb shocks

What is the correct answer?

4

An elastic bar is fixed at the upper end and loaded at the lower end by a falling weight. The shock load produced can be reduced by

A. Increasing the length of bar

B. Decreasing the cross-sectional area of the bar

C. Decreasing the modulus of elasticity of the bar

D. All of the above

What is the correct answer?

4

In designing a connecting rod, it is considered like __________ for buckling about X-axis.

A. Both ends hinged

B. Both ends fixed

C. One end fixed and the other end hinged

D. One end fixed and the other end free

What is the correct answer?

4

In order to ensure self locking in a screw jack, it is essential that helix angle is __________ friction angle.

A. Larger than

B. Smaller than

C. Equal to

D. None of these

What is the correct answer?

4

The value of stress concentration factor depends upon

A. Material and geometry of the part

B. Geometry of the part

C. Material of the part

D. None of these

What is the correct answer?

4

The edges of a boiler plate are bevelled to an angle of

A. 30°

B. 45°

C. 60°

D. 80°

What is the correct answer?

4

The plasticity is the property of a material which enables it to

A. Regain its original shape after deformation when the external forces are removed

B. Draw into wires by the application of a tensile force

C. Resist fracture due to high impact loads

D. Retain deformation produced under load permanently

What is the correct answer?

4

Lewis form factor for 14 ½° composite and full depth involute system is (where T = Number of teeth)

A. 0.124 - (0.684/T)

B. 0.154 - (0.912/T)

C. 0.175 - (0.841/T)

D. None of these

What is the correct answer?

4

The notch sensitivity q is expressed in terms of fatigue stress concentration factor Kf and theoretical stress concentration factor Kt as

A. (Kf + 1)/ (Kt + 1)

B. (Kf - 1)/ (Kt - 1)

C. (Kt + 1)/ (Kf + 1)

D. (Kt - 1)/ (Kf - 1)

What is the correct answer?

4

The stretching in a belt can be controlled by __________ the stress in the belt.

A. Reducing

B. Increasing

C. Both A and B

D. None of these

What is the correct answer?

4

The designation M 33 × 2 of a bolt means

A. Metric threads of 33 numbers in 2 cm

B. Metric threads with cross-section of 33 mm

C. Metric threads of 33 mm outside diameter and 2 mm pitch

D. Bolt of 33 mm nominal diameter having 2 threads per cm

What is the correct answer?

4

At low temperatures (say 75°C) the notched bar impact value of steel

A. Increases markedly

B. Decreases markedly

C. Remain same

D. Depends on heat treatment carried out

What is the correct answer?

4

In skew bevel gearing, the axes of shafts are

A. Intersecting and the teeth are curved

B. Non-intersecting and nonparallel and the teeth are curved

C. Non-intersecting and non-parallel and the teeth are straight

D. None of the above

What is the correct answer?

4

Plastic flow in ductile materials

A. Increases the seriousness of static loading stress concentration

B. Lessens the seriousness of static loading stress concentration

C. Has no effect on it

D. Depends on other considerations

What is the correct answer?

4

For a shoe brake, the equivalent coefficient of friction is equal to (where μ = Actual coefficient of friction, and θ = Semi-block angle)

A. 2μ sinθ/(θ + sinθ)

B. μ sinθ/(2θ + sin 2θ)

C. 4μ sinθ/(θ + sinθ)

D. 4μ sinθ/(2θ + sin 2θ)

What is the correct answer?

4

For longitudinal joint in boilers, the type of joint used is

A. Butt joint with single cover plate

B. Butt joint with double cover plate

C. Lap joint with one ring overlapping the other

D. Any one of the above

What is the correct answer?

4

Which of the following has threads at both ends?

A. Bolt

B. Tap bolt

C. Stud

D. None of these

What is the correct answer?

4

Taper on the cotter and slot is provided

A. On both the sides

B. On one side only

C. On none of the sides

D. May be provided anywhere

What is the correct answer?

4

The relation between the pitch of the chain (p) and pitch circle diameter of the sprocket (D) is given by (where T = Number of teeth on the sprocket)

A. p = D sin (90°/T)

B. p = D sin (120°/T)

C. p = D sin (180°/T)

D. p = D sin (360°/T)

What is the correct answer?

4

In the levers of first type, the mechanical advantage is __________ one.

A. Less than

B. Equal to

C. More than

D. None of these

What is the correct answer?

4

In thrust bearings, the load acts

A. Along the axis of rotation

B. Parallel to the axis of rotation

C. Perpendicular to the axis of rotation

D. In any direction

What is the correct answer?

4

A locking device extensively used in marine type connecting rod ends is a

A. Jam nut

B. Castle nut

C. Sawn nut

D. Ring nut

What is the correct answer?

4

The property of a material which enables it to resist fracture due to high impact loads is known as

A. Elasticity

B. Endurance

C. Strength

D. Toughness

What is the correct answer?

4

The dedendum circle diameter is equal to (where φ = Pressure angle)

A. Pitch circle diameter × cosφ

B. Addendum circle diameter × cosφ

C. Clearance circle diameter × cosφ

D. Pitch circle diameter × sinφ

What is the correct answer?

4

In levers, leverage is the ratio of

A. Load lifted to the effort applied

B. Mechanical advantage to the velocity ratio

C. Load arm to the effort arm

D. Effort arm to the load arm

What is the correct answer?

4

The shearing stresses in the inner face as compared to outer face of the wire in a heavy close coiled spring is

A. Larger

B. Smaller

C. Equal

D. Larger/smaller depending on diameter of spring coil

What is the correct answer?

4

Cold working

A. Increases the fatigue strength

B. Decreases the fatigue strength

C. Has no influence on fatigue strength

D. Alone has no influence on fatigue strength

What is the correct answer?

4

In the levers of third type, the mechanical advantage is __________ one.

A. Less than

B. Equal to

C. More than

D. None of these

What is the correct answer?

4

Taper usually provided on cotter is

A. 1 in 5

B. 1 in 10

C. 1 in 24

D. 1 in 40

What is the correct answer?

4

The tension on the slack side of the belt is __________ the tension on the tight side of the belt.

A. Equal to

B. Less than

C. Greater than

D. None of these