The electrode tip diameter (d) in spot welding should be equal to (where t = Thickness of plate to be welded)
t
1.5 t
3 t
6 t
Correct Answer :
A. t
Related Questions
A hacksaw blade cuts on the
Forward stroke
Return stroke
Both forward and return strokes
Cutting depends upon the direction of force
Which of the following statement is wrong?
The hot chamber die casting machine is used for casting zinc, tin, lead and other low melting alloys.
The cold chamber die casting machine is used for casting aluminium, magnesium, copper base alloys and other high melting alloys.
The castings produced by centrifugal casting method have open and coarse grained structure.
All of the above
The dowels are
Wooden nails
Box nails
Wire nails
None of these
Tandem drawing of wires and tubes is necessary because
It is not possible to reduce at one stage
Annealing is needed between stages
Accuracy in dimensions is not possible otherwise
Surface finish improves after every drawing stage
Seam welding is a
Continuous spot welding process
Multi-spot welding process
Arc welding process
Process used for joining round bars
In a ________, two or more operations are performed simultaneously at the single stroke of the ram.
Simple die
Progressive die
Combination die
Compound die
Structural sections such as rails, angles, I-beams are made by
Hot rolling
Hot drawing
Hot piercing
Hot extrusion
The mode of deformation of the metal during spinning is
Bending
Stretching
Rolling and stretching
Bending and stretching
Which of the following welding process uses non-consumable electrodes?
TIG welding
MIG welding
Manual arc welding
Submerged arc welding
The flux commonly used in brazing is
Zinc chloride
Ammonium chloride
Rosin plus alcohol
Borax
The surface to be left unmachined is marked on the pattern by
Red colour
Yellow colour
Black colour
Blue colour
The material which can be best cut with oxygen cutting process is
Mild steel
Brass
Copper
Aluminium
Thread rolling is restricted to
Ferrous materials
Ductile materials
Hard materials
None of these
In ________ welding, the weld may be made either from left to right or from right to left.
Forehand
Backhand
Vertical
None of these
The process used to improve fatigue resistance of the metal by setting up compressive stresses in its surface, is known as
Hot piercing
Extrusion
Cold peening
Cold heading
The temperature of the inner luminous cone of neutral flame is about
1000°C
1250°C
2100°C
3200°C
In a _________, the molten metal is poured and allowed to solidify while the mould is revolving.
Die casting method
Slush casting method
Permanent mould casting method
Centrifugal casting method
When the molten metal is fed in the cavity of a metallic mould by gravity, the method of casting is known as
Die casting method
Slush casting method
Permanent mould casting method
Centrifugal casting method
In arc welding, the temperature of heat produced by the electric arc is of the order of
3000°C to 4000°C
4000°C to 5000°C
5000°C to 6000°C
6000°C to 7000°C
In order to ram the sand harder at the back of the mould and softer on the pattern face, a ________ is used.
Sand slinger
Squeezing machine
Jolt machine
Stripper plate machine
The most preferred process for casting gas turbine blades is
Die casting
Shell moulding
Investment moulding
Sand casting
The cold working of metals is carried out
At the recrystallisation temperature
Below the recrystallisation temperature
Above the recrystallisation temperature
At any temperature
In welding magnesium with TIG arc welding, direct current with _________ is used.
Straight polarity
Reversed polarity
Both (A) and (B)
None of these
Lancing is the operation of
Cutting a sheet of metal in a straight line along the length
Removal of metal to the desired shape from the edge of a plate
Cutting a sheet of metal through part of its length and then bending the cut portion
Bending a sheet of metal along a curved axis
A jolt machine is used to
Ram the sand harder at the pattern face with decreasing hardness towards the back of the mould
Ram the sand harder at the back of the mould and softer on the pattern face
Produce uniform sand hardness throughout the mould
Produce uniform packing of sand in the mould
During drawing operation, the states of stress in cup would include
Compressive stress in the flange
Tensile stress in the wall
Both (A) and (B)
None of these
The operation of straightening a curved sheet metal, is known as
Drawing
Squeezing
Coining
Planishing
The electrode tip diameter (d) in spot welding should be equal to (where t = Thickness of plate to be welded)
t
1.5 t
3 t
6 t
In electric resistance welding, pressure applied varies from
1 to 5 MPa
5 to 10 MPa
10 to 25 MPa
25 to 55 MPa
The binder commonly used in making oil sand, is
Clay type binder
Organic type binder
Inorganic type binder
Any one of these