Motion of a piston in the cylinder of a steam engine
Motion of a square bar in a square hole
Motion of a shaft with collars at each end in a circular hole
All of the above
D. All of the above
Stable
Unstable
Isochronous
None of these
Second inversion of double slider crank chain
Third inversion of double slider crank chain
Second inversion of single slider crank chain
Third inversion of slider crank chain
One binary joint
Two binary joints
Three binary joints
Four binary joints
Whitworth quick return mechanism
Hand pump
Oscillating cylinder engine
All of the above
Knife edge follower
Flat faced follower
Spherical faced follower
Roller follower
Free vibration
Forced vibration
Damped vibration
Under damped vibration
(1/2). μ W cosec α (r₁ + r₂)
(2/3).μ W cosec α (r₁ + r₂)
(1/2). μ W cosec α [(r₁³ - r₂³)/(r₁² - r₂²)]
(2/3). μ W cosec α [(r₁³ - r₂³)/(r₁² - r₂²)]
P = W tan α
P = W tan (α + φ)
P = W (sin α + μ cos α)
P = W (cos α + μ sin α)
(1 - sinφ)/(1 + sinφ)
(1 + sinφ)/(1 - sinφ)
(1 - tanφ)/(1 + tanφ)
(1 + tanφ)/(1 - tanφ)
Parallel to the link joining the points
Perpendicular to the link joining the points
At 45° to the link joining the points
None of the above
Deep groove ball bearing
Double row self aligning ball bearing
Double row spherical roller bearing
Cylindrical roller bearing
Thompson indicator
Richard indicator
Simplex indicator
Thomson indicator
One-half
Two-third
n times
1/n times
Minimise the effect of primary forces
Minimise the effect of secondary forces
Have perfect balancing
To start the locomotive quickly
(1/2π). √(kG/g)
(1/2π). √(2kG/g)
2π. √(kG/g)
2π. √(2kG/g)
A small value of pressure angle
A large value of pressure angle
There is no such relation with pressure angle
Something else
[(r² + R²) cosφ]/2
[(r² + R²) sinφ]/2
[(r + R) cosφ]/2
[(r + R) sinφ]/2
Zero
Minimum
Maximum
None of these
Lower pair
Higher pair
Self-closed pair
Force-closed pair
The tip of a tooth of a mating gear digs into the portion between base and root circles
Gears do not move smoothly in the absence of lubrication
Pitch of the gears is not same
Gear teeth are undercut
Spur gear
Helical gear
Bevel gear
Spiral gear
Directly proportional to the distance from the points to the instantaneous centre and is parallel to the line joining the point to the instantaneous centre
Directly proportional to the distance from the points to the instantaneous centre and is perpendicular to the line joining the point to the instantaneous centre
Inversely proportional to the distance from the points to the instantaneous centre and is parallel to the line joining the point to the instantaneous centre
Inversely proportional to the distance from the points to the instantaneous centre and is perpendicular to the line joining the point to the instantaneous centre
At the origin
Below the origin
Above the origin
Any one of these
m₁r₂ = m₂r₁
m₁r₁ = m₂r₂
m₁m₂ = r₁r₂
None of these
More than
Less than
Same as
None of these
Upward
Downward
Forward
Backward
Balanced completely
Balanced partially
Balanced by secondary forces
Not balanced
D₁/D₂
D₂/D₁
D₁.D₂
D₁
Halved
Doubled
Quadrupled
None of these
Offset between centre lines of cam and follower
Lift of follower
Angle of ascent
All of the above