Related Questions
What is the correct answer?
4
This type of surface may be a plane, a single curved surface, or a warped surface:
What is the correct answer?
4
The distance a screw thread advances axially in one turn is the:
What is the correct answer?
4
The ________ tool on the Dimension tool bar places the length of an arch on a drawing.
What is the correct answer?
4
A full scale technical drawing will have a scale factor of ________.
What is the correct answer?
4
A line drawn with a long section, short dash, and another long section is a ________.
C. Center axis of a hidden cylinder
What is the correct answer?
4
Acceptable parts must not extend beyond this:
What is the correct answer?
4
Referring to the fractional inches to decimal inches to millimetre conversion chart on page 55 what is the equivalent mm measurement of 3/16 inch.
What is the correct answer?
4
In these drawings it is necessary to show cut surfaces and distinguish between adjacent parts:
What is the correct answer?
4
These maps are used in planning installations of trees, shrubbery, drives, and other garden features:
What is the correct answer?
4
This type of drawing shows two lines representing the pipe diameter:
What is the correct answer?
4
When filling an area with a hatch pattern in Auto-CAD the drafter needs to be able to ________.
A. See the entire bounding area to hatch
D. Set the layer to Defpoints
What is the correct answer?
4
5.These items typically are not used in new designs, but are still common in high-power amplifiers:
What is the correct answer?
4
When setting up a mechanical drawing in Auto-CAD the drafter should set the units to ________.
What is the correct answer?
4
In an assembly section, these parts should have their section lines left out or shown solid black:
What is the correct answer?
4
The title block used on working drawings should include the __________.
What is the correct answer?
4
A round is a rounded surface on the ________ corner of a part.
What is the correct answer?
4
Two-point perspective is also known as:
What is the correct answer?
4
These are vertical distances above a common datum, reference plane, or point:
What is the correct answer?
4
The Conceptual Visual Style tool is located on the ________ toolbar.
What is the correct answer?
4
This type of rapid prototyping system uses a laser to fuse powdered metals, plastics, or ceramics:
A. Fused deposition modeling
B. Stereo lithography apparatus
D. Selective laser sintering
What is the correct answer?
4
Dimensions are used on the elevation plan to describe ________.
A. Finished floor elevations
What is the correct answer?
4
When using the descriptive geometry method to create an auxiliary view the drafter should __________.
A. Rotate the snap grid to the same angle of the inclined plane
B. Offset the right vertical line of the front view
C. Rotate the top line of the front view 45 degrees
D. Offset the top line of the front view 2 inches
What is the correct answer?
4
In a CAD system, you can draw an ellipse by specifying these:
B. The midpoint and end points
C. The center and major and minor axes
What is the correct answer?
4
These drawings are given to contractors to perform work or manufacture individual parts:
What is the correct answer?
4
This type of circuit is a semiconductor wafer or chip:
What is the correct answer?
4
When using the direct entry method to create a horizontal line exactly three inches long the drafter should ________ first.
A. Pull the line from away from the starting point very carefully
B. Insure that Ortho is on
C. Enter 3 for the length of the line
D. Read the coordinate position on the Dynamic Readout
What is the correct answer?
4
In this type of auxiliary view, a break line is used to indicate the imaginary break in the views:
What is the correct answer?
4
When only a small section of an interior area needs to be revealed the drafter can use a ________ section.
What is the correct answer?
4
This is a line terminated by arrowheads, indicating the direction and extent of a dimension:
What is the correct answer?
4
To avoid having to dimension to a hidden feature the drafter can utilize a ________ section.