Home
Current Affairs January 2024

What is the correct answer?

4

The gas constant (R) is equal to the __________ of two specific heats.

A. Sum

B. Difference

C. Product

D. Ratio

Correct Answer :

B. Difference


Related Questions

What is the correct answer?

4

One kilowatt is equal to

A. 1 N-m/s

B. 100 N-m

C. 1000 N-m/s

D. 1 × 106 N-m/s

What is the correct answer?

4

Which of the following statement is incorrect?

A. The liquid fuels have higher calorific value than solid fuels

B. The solid fuels have higher calorific value than liquid fuels

C. A good fuel should have low ignition point

D. The liquid fuels consist of hydrocarbons

What is the correct answer?

4

The distance between the centres of the rivets in adjacent rows of zigzag riveted joint is known as

A. Pitch

B. Back pitch

C. Diagonal pitch

D. Diametric pitch

What is the correct answer?

4

If a material expands freely due to heating it will develop

A. Thermal stresses

B. Tensile stress

C. Bending

D. No stress

What is the correct answer?

4

For a simply supported beam of length l, when a concentrated load W is applied in the centre of the beam, the maximum deflection is

A. 5WL³/ 384EI

B. WL³/384EI

C. WL³/ 348EI

D. WL³/ 48EI

What is the correct answer?

4

A boiler shell 200 cm diameter and plate thickness 1.5 cm is subjected to internal pressure of 1.5 MN/m, and then the hoop stress will be

A. 30 MN/m²

B. 50 MN/m²

C. 100 MN/m²

D. 200 MN/m²

What is the correct answer?

4

Workdone during adiabatic expansion is given by (where p1 v1, T1 = Pressure, volume and temperature for the initial condition of gas, p2, v2, T2 = Corresponding values for the final condition of gas, R = Gas constant, and γ = Ratio of specific heats)

A. (p1 v1 - p2 v2)/(γ - 1)

B. [m R (T1 - T2)] /(γ - 1)

C. [m R T1/(γ - 1)][1 - (p2 v2 /p1 v1)]

D. All of these

What is the correct answer?

4

The natural petroleum may be separated into

A. Petrol

B. Kerosene

C. Fuel oil

D. Lubricating oil

What is the correct answer?

4

If percentage reduction in area of a certain specimen made of material 'A' under tensile test is 60% and the percentage reduction in area of a specimen with same dimensions made of material 'B' is 40%, then

A. The material A is more ductile than material B

B. The material B is more ductile than material A

C. The ductility of material A and B is equal

D. The material A is brittle and material B is ductile

What is the correct answer?

4

In an irreversible process, there is a

A. Loss of heat

B. No loss of heat

C. Gain of heat

D. No gain of heat

What is the correct answer?

4

A thin cylindrical shell of diameter (D) and thickness (t) is subjected to an internal pressure (p). The ratio of longitudinal strain to volumetric strain is

A. (m - 1)/ (2m - 1)

B. (2m - 1)/ (m - 1)

C. (m - 2)/ (3m - 4)

D. (m - 2)/ (5m - 4)

What is the correct answer?

4

The assumption made in Euler's column theory is that

A. The failure of column occurs due to buckling alone

B. The length of column is very large as compared to its cross-sectional dimensions

C. The column material obeys Hooke's law

D. All of the above

What is the correct answer?

4

The total strain energy stored in a body is termed a

A. Resilience

B. Proof resilience

C. Modulus of resilience

D. Toughness

What is the correct answer?

4

The radius of the Mohrs circle in the given figure is equal to

A. Sum of two principal stresses

B. Difference of two principal stresses

C. Half the sum of two principal stresses

D. Half the difference of two principal stresses

What is the correct answer?

4

If both Stirling and Carnot cycles operate within the same temperature limits, then efficiency of Stirling cycle as compared to Carnot cycle

A. More

B. Less

C. Equal

D. Depends on other factors

What is the correct answer?

4

The value of modulus of elasticity for mild steel is of the order of

A. 2.1 × 10⁵ kg/cm²

B. 2.1 × 10⁶ kg/cm²

C. 2.1 × 10⁷ kg/cm²

D. 0.1 × 10⁶ kg/cm²

What is the correct answer?

4

The value of cp/cv for air is

A. 1

B. 1.4

C. 1.45

D. 2.3

What is the correct answer?

4

Flow stress corresponds to

A. Fluids in motion

B. Breaking point

C. Plastic deformation of solids

D. Rupture stress

What is the correct answer?

4

When shear force at a point is zero, then bending moment is _________ at that point.

A. Zero

B. Minimum

C. Maximum

D. Infinity

What is the correct answer?

4

The maximum shear stress, in the given figure, is equal to __________ of the Mohr's circle.

A. Radius

B. Diameter

C. Circumference

D. Area

What is the correct answer?

4

Which of the following is a proper sequence?

A. Proportional limit, elastic limit, yielding, failure

B. Elastic limit, proportional limit, yielding, failure

C. Yielding, proportional limit, elastic limit, failure

D. None of the above

What is the correct answer?

4

The amount of heat required to raise the temperature of __________ water through one degree is called kilojoules.

A. 1 g

B. 10 g

C. 100 g

D. 1000 g

What is the correct answer?

4

Modulus of rigidity may be defined as the ratio of

A. Linear stress to lateral strain

B. Lateral strain to linear strain

C. Linear stress to linear strain

D. Shear stress to shear strain

What is the correct answer?

4

Formula based on IS codes is based on

A. Straight line formula

B. Eulers formula

C. Rankines formula

D. Secant formula

What is the correct answer?

4

One reversible heat engine operates between 1600 K and T2 K and another reversible heat engine operates between T2 K and 400 K. If both the engines have the same heat input and output, then temperature T2 is equal to

A. 800 K

B. 1000 K

C. 1200 K

D. 1400 K

What is the correct answer?

4

Which of the following statement is correct?

A. The stress is the pressure per unit area

B. The strain is expressed in mm

C. Hook's law holds good upto the breaking point

D. Stress is directly proportional to strain within elastic limit

What is the correct answer?

4

The safe twisting moment for a compound shaft is equal to the

A. Maximum calculated value

B. Minimum calculated value

C. Mean value

D. Extreme value

What is the correct answer?

4

The total energy of a molecule is shared equally by the various degrees of freedom possessed by it. This law is known as

A. Law of equipartition of energy

B. Law of conservation of energy

C. Law of degradation of energy

D. None of these

What is the correct answer?

4

The value of 1 mm of Hg is equal to

A. 1.333 N/m2

B. 13.33 N/m2

C. 133.3 N/m2

D. 1333 N/m2

What is the correct answer?

4

The pull required to tear off the plate per pitch length is (where p = Pitch of rivets, t = Thickness of plates, and σt, τ and σc = Permissible tensile, shearing and crushing stresses respectively)

A. (p - 2d) t × σc

B. (p - d) t × τ

C. (p - d) t × σt

D. (2p - d) t × σt