Related Questions
What is the correct answer?
4
Which of the following is a common material used in wire-wound resistors?
What is the correct answer?
4
The power factor of a circuit is equal to
What is the correct answer?
4
What determines the magnitude of electric current?
A. The rate at which electrons are produced
B. The type of material used
C. The current carrying capacity of the circuit
D. The rate at which electrons pass a given point
What is the correct answer?
4
The distance between the capacitor plates increases two timesa then its capacitance
What is the correct answer?
4
The second strip of an electronic resistor color-code represents
B. The second digit of the value
What is the correct answer?
4
When two coils of identical reactance are in parallel without mutual inductancea the reactance of the combination is ___ the reactance of each coil.
What is the correct answer?
4
Which of the following does not refer to electrical energy?
What is the correct answer?
4
The Q-factor of a parallel resonant circuit is also known as
A. Voltage magnification factor
B. Current magnification factor
C. Gain magnification factor
D. Resonance magnification factor
What is the correct answer?
4
Which of the following does not affect resistance?
What is the correct answer?
4
When the temperature of copper wire is increased its resistance is
What is the correct answer?
4
The reason why alternating current can induce voltage is
A. It has high peak value
B. It has a stronger magnetic field than direct current
C. It has a constant magnetic field
D. It has a varying magnetic field
What is the correct answer?
4
Which of the following materials has the lowest dielectric strength?
What is the correct answer?
4
When two complex conjugates are subtracteda the result is a
A. Quadrature component only
What is the correct answer?
4
When two unequal values of resistors are connected in parallel across a dc sourcea greater current flows through the
C. Higher wattage resistance
D. Lower wattage resistance
What is the correct answer?
4
For a triangular and sawtooth waveform the rms voltage or current equals
B. 0.577 times peak value
C. 0.577times average value
What is the correct answer?
4
In dividing or multiplying phasor quantitiesa ___ form is used.
What is the correct answer?
4
What value of R is needed with a 0.05 F Cfor an RCtime constant of 0.02 s?
What is the correct answer?
4
VL= VCin a series RLCcircuit when
A. The value of the impedance is minimum
B. The power factor is zero
C. The current leads the total voltage by 90�
D. The total voltage is zero
What is the correct answer?
4
The usual load of a dc circuit is a/an
D. Both inductor and capacitor
What is the correct answer?
4
What is the rms value of a square wave?
B. Equals its peak-to-peak value
C. Peak divided by square root of two
What is the correct answer?
4
What is the conductance of a circuit having three 10 resistors in parallel?
What is the correct answer?
4
What is the specific resistance of a pure silicon?
What is the correct answer?
4
An impedance given by 90 -45� is a/an ___ impedance.
What is the correct answer?
4
The average value of a triangular or sawtooth wave is _____ times its peak value.
What is the correct answer?
4
A factor that states how much the resistance changes for a change in temperature?
C. Coefficient of temperature change
D. Temperature coefficient of resistance
What is the correct answer?
4
What is the efficiency under the conditions of maximum power transfer?
What is the correct answer?
4
What fusion of elements is without chemical action between them?
What is the correct answer?
4
The ratio of the flux density to the electric field intensity in the dielectric is called
What is the correct answer?
4
The result of rust in electrical (wire) connection is
What is the correct answer?
4
A coil of inductance L has an inductive reactance of XLin an ac circuit in which the effective current is I. The coil is made from a superconducting material. The rate at which power is dissipated in the coil is