Related Questions
What is the correct answer?
4
The rivet head used for boiler plate riveting is usually
What is the correct answer?
4
The included angle for the British Association thread is
What is the correct answer?
4
The maximum shear stress theory is used for
What is the correct answer?
4
Elastic nut is a locking device in which
A. One small nut is tightened over main nut and main nut tightened against smaller one by loosening, creating friction jamming
B. A slot is cut partly in middle of nut and then slot reduced by tightening a screw
C. Hard fibre or nylon cotter is recessed in the nut and becomes threaded as the nut is stewed on the bolt causing a tight grip
D. Through slots are made at top and a cotter pin is passed through these and a hole in the bolt, and cotter pin splitted and bent in reverse direction at other end
What is the correct answer?
4
The dedendum circle diameter is equal to (where φ = Pressure angle)
A. Pitch circle diameter × cosφ
B. Addendum circle diameter × cosφ
C. Clearance circle diameter × cosφ
D. Pitch circle diameter × sinφ
What is the correct answer?
4
For standard coarse threads of nut, the threads will be as strong in failure by shear as the bolt in tension, if the height of nut (h) is approximately
What is the correct answer?
4
The radial distance of a tooth from the pitch circle to the top of the tooth is called
What is the correct answer?
4
The shock resistance of steel is increased by adding
What is the correct answer?
4
A key capable of tilting in a recess milled out in a shaft is known as
What is the correct answer?
4
When a bolt is subjected to shock loading, the resilience of the bolt should be considered in order to prevent breakage at the
What is the correct answer?
4
The cold working of metals is carried out __________ the recrystallisation temperature.
What is the correct answer?
4
In static loading, stress concentration is more serious in
C. Brittle as well as ductile materials
What is the correct answer?
4
Eulers formula for a mild steel column is not valid if the slenderness ratio is
What is the correct answer?
4
Turn buckle has
A. Right hand threads on bout ends
B. Left hand threads on both ends
C. Left hand threads on one end and right hand threads on other end
What is the correct answer?
4
In the levers of third type, the mechanical advantage is __________ one.
What is the correct answer?
4
The velocity of sliding ________ the distance of the point of contact from the pitch point.
A. Is directly proportional to
B. Is inversely proportional to
C. Is equal to cos φ multiplied by
What is the correct answer?
4
The product of the diametral pitch and circular pitch is equal to
What is the correct answer?
4
The allowable static stress for steel gears is approximately __________ of the ultimate tensile stress.
What is the correct answer?
4
The ball bearings are, usually, made from
What is the correct answer?
4
The elasticity is the property of a material which enables it to
A. Regains its original shape after deformation when the external forces are removed
B. Draw into wires by the application of a tensile force
C. Resists fracture due to high impact loads
D. Retain deformation produced under load permanently
What is the correct answer?
4
For a square key made of mild steel, the shear and crushing strength are related as
A. Shear strength is equal to crushing strength
B. Shear strength is greater than crushing strength
C. Shear strength is less than crushing strength
What is the correct answer?
4
Belt slip may occur due to
C. Driving pulley too small
What is the correct answer?
4
A circular shaft can transmit a torque of 5 kN-m. If the torque is reduced to 4 kN-m, then the maximum value of bending moment that can be applied to the shaft is
What is the correct answer?
4
A special case of ductility which permits materials to be rolled or hammered into thin sheets, is called
What is the correct answer?
4
The maximum normal stress theory is used for
What is the correct answer?
4
If d is the normal diameter of a bolt in mm, then the initial tension in kg in a bolt used for making a fluid tight joint as for steam engine cover joint is calculated by the relation
What is the correct answer?
4
The included angle between the sides of V-belt is
What is the correct answer?
4
When an open coiled helical compression spring is subjected to an axial compressive load, the stress induced in the wire is
What is the correct answer?
4
Form coefficient of spring is
A. Ratio of coil diameter to wire diameter
B. Load required to produce unit deflection
C. Its capability of storing energy
D. Concerned with strength of wire of spring
What is the correct answer?
4
According to I.B.R., the distance between the rows of rivets, for equal number of rivets in more than one row for lap joint or butt joint (chain riveting) shall not be less than