Related Questions
What is the correct answer?
4
'Flare tower' used in industry is meant for
A. Venting off (after burning) the excess inflammable/toxic gases at high pressure
B. Absorbing the pollutant gases from the furnace exhaust
C. Cooling of furnace exhaust gases
What is the correct answer?
4
Thermit welding is categorised as the __________ welding.
What is the correct answer?
4
Limestone is added in the blast furnace (during pig iron manufacture) to
A. Form slag by combining with impurities
B. Supply heat by undergoing exothermic reaction with impurities
C. Reduce the coke consumption
What is the correct answer?
4
__________ wire is never used for making the heating element.
What is the correct answer?
4
Drossing is a __________ operation.
What is the correct answer?
4
The efficiency of a Carnot heat engine operating between absolute temperatures T1 and T2 (when, T1 > T2) is given by (T1 - T2)/T1. The co-efficient of performance (CO.P.) of a Carnot heat pump operating between T1 and T2 is given by
What is the correct answer?
4
Wavelength of radiation emitted by a body depends on the __________ of its surface.
What is the correct answer?
4
Gage pressure within a spherical droplet of a fluid is 'p'. What will be gage pressure within a bubble of the same size & of the same fluid?
What is the correct answer?
4
If the demand for an item is trebled and the order cost is reduced to one third, then the economic order quantity
C. Decreases by a factor of 3
D. Decreases by a factor of 1/3
What is the correct answer?
4
In the diving apparatus, helium is used along with oxygen, because it is
B. Not soluble in blood at high pressure
D. Completely miscible with oxygen
What is the correct answer?
4
Powder metallurgy process does not make metal powder by
D. Electrolytic deposition
What is the correct answer?
4
Stresses encountered in the metal forming processes are less than the __________ of the material.
D. Limit of proportionality
What is the correct answer?
4
Which of the following phenomenon will exhibit the minimum heat transfer?
B. Forced convection in air
C. Free convection in air
What is the correct answer?
4
Temperature of hot gases flowing in a pipe is measured by a thermocouple inserted in the thermal well. The thermal well made of __________ will facilitate the most accurate measurement of the temperature.
What is the correct answer?
4
Larger length & diameter water pipes are made by
A. Electrical resistance welding
C. Semi-centrifugal casting
What is the correct answer?
4
Wave length of X-rays is about 1 angstrom; however it cannot pass through a sheet of
What is the correct answer?
4
Increasing the carbon content of steel
A. Reduces the upper shelf energy
B. Increasing the ductility transition temperature
What is the correct answer?
4
Closeness of packing is maximum in case of __________ crystal lattice.
What is the correct answer?
4
Steel produced from phosphatic iron is __________ in nature.
What is the correct answer?
4
The property of material, by which a given amount of energy is absorbed by it without plastic deformation, is called the
What is the correct answer?
4
Ferromagnetic materials owe their properties to __________ inner sub-shells.
What is the correct answer?
4
Wood is a/an __________ material.
What is the correct answer?
4
A polymer is termed as an 'elastomer', if its percentage elongation is more than 100%. An elastomer is termed as 'rubber' if its percentage elongation is more than __________ percent.
What is the correct answer?
4
Calorific value of __________ are almost same.
A. Lignite & anthracite coal
D. Coal gas & natural gas
What is the correct answer?
4
While the thermosetting polymers are amorphous in nature, the thermoplastic polymers are either amorphous or crystalline. The crystalline polymers are characterised by the
C. Better finish and surface appearance
D. High plastic deformation
What is the correct answer?
4
In Imperial Smelting Process for extraction of zinc, zinc vapour thus produced is quenched in the external condenser by the use of the following:
A. Jet of water at high pressure
C. Mixture of water and air
What is the correct answer?
4
Which of the following forces does not act on a fluid at rest?
What is the correct answer?
4
Which of the following is normally not found in both the S.I. (petrol) & C.I. (diesel) engines?
What is the correct answer?
4
Which of the following is not a ferromagnetic material?
What is the correct answer?
4
Yield strength of a material is determined by the __________ test.