Related Questions
What is the correct answer?
4
For preparation of porous bearings by powder metallurgy, preferred particle shape is
What is the correct answer?
4
If the demand for an item is trebled and the order cost is reduced to one third, then the economic order quantity
C. Decreases by a factor of 3
D. Decreases by a factor of 1/3
What is the correct answer?
4
In chemical dehumidification process
A. Wet bulb temperature increases
B. Dry bulb temperature remains constant
C. Dew point temperature increases
D. Dry bulb temperature increases
What is the correct answer?
4
To counteract the bad effects of strain hardening on a cold formed part, it must be
What is the correct answer?
4
Particle nature of cathode rays is proved due to the fact that they
A. Travel in a straight line
B. Get deflected by magnetic electric field
D. Heat the exposed material
What is the correct answer?
4
Increase in the entropy of a system represents the
B. Decrease in system pressure
C. Increase in the availability of energy
D. Increase in the temperature
What is the correct answer?
4
Inertial forces are obtained, when the elastic forces are multiplied by __________ number.
What is the correct answer?
4
Lead is added to 60:40 brass primarily to improve
What is the correct answer?
4
A thin, flat & square plate measuring 2 m × 2 m is freely hanging in ambient air at 25°C. It is exposed to the solar radiation falling on one side of the plate at the rate of 500 W/m2. The plate temperature will remain constant at 30°C, if the convective heat transfer co-efficient is __________ W/m2 °C.
What is the correct answer?
4
The dimensional formula of bulk modulus of elasticity is same as that of the
What is the correct answer?
4
Angular displacement can be measured suitably by a
B. Linear variable differential transducer (LVDT)
What is the correct answer?
4
Dryness fraction of dry steam is
What is the correct answer?
4
Eutectoid composition of carbon steel at room temperature is
What is the correct answer?
4
In practice, the compression ratio of compression-ignition (CI) engine ranges from
What is the correct answer?
4
Consideration of the creep is the most important in case of the
B. Piston of an I. C. engine
C. Flywheel of steam engine
What is the correct answer?
4
Referring to the periodic table of elements, it is found that with increasing atomic number. The atomic size in the same
What is the correct answer?
4
Which of the following is an acidic constituent of B.F. slag?
A.
What is the correct answer?
4
Main constituent of bone ash is
What is the correct answer?
4
Catalyst used in the catalytic converter employed in automobiles to convert CO into CO2 and for complete oxidation of un-burnt hydrocarbons is
What is the correct answer?
4
Heat transfer to the water wall in a high pressure water wall type boiler furnace is mainly by
What is the correct answer?
4
The majority charge carriers in p-type silicon are
What is the correct answer?
4
Maximum change in the hardness of martensite occurs in the carbon content range of __________ percent in steel.
What is the correct answer?
4
Which of the following relationships is correct for relating the three elastic constants of an isotropic elastic material (where, E = Young's modulus, G = Modulus of rigidity or shear modulus v = Poisson's ratio)?
What is the correct answer?
4
Oxyacetylene reducing flame is used while carrying out welding on
What is the correct answer?
4
A furnace is made of a refractory brick wall of thickness 0.5 metre and thermal conductivity 0.7 W/m.°K For the same temperature drop and heat loss, this refractory wall can be replaced by a layer of diatomaceous earth of thermal conductivity 0.14 W/m.K and thickness __________ metre.
What is the correct answer?
4
Plastics as a material of construction suffer from the drawback of low
What is the correct answer?
4
Superheating of steam is done at constant
What is the correct answer?
4
The expected efficiency of a single riveted lap joint is of the order of 50%. If the thickness of the plate is increased four times, then the rivet diameter will have to be increased __________ times.
What is the correct answer?
4
Which of the following approaches the ideal gas behaviour most closely?
What is the correct answer?
4
__________ fluid force is not considered in the Navier-Stokes equation.