Related Questions
What is the correct answer?
4
The __________ of a double acting reciprocating pump as compared to the single acting pump will be almost double.
What is the correct answer?
4
Maximum consumption of limestone is in the __________ industry.
What is the correct answer?
4
Which of the following fastening devices has a head at one end and a nut fitted to the other?
What is the correct answer?
4
Cast iron contains __________ percent carbon.
What is the correct answer?
4
The laminar boundary layer thickness in zero pressure gradient flow over a flat plate along the x-direction varies as x0.5 while the thickness of turbulent boundary layer varies as (where, x = distance from the leading edge)
What is the correct answer?
4
Pick out the wrong statement about nucleate boiling.
A. Bubble generation is by expansion of entrapped gas/vapour at small cavities in the surface
B. Surface temperature is greater than the saturation temperature of the liquid
C. Heat transfer from the surface of the liquid is less than that in film boiling
D. The temperature is less than that of film boiling
What is the correct answer?
4
Thermal conductivity of a material does not depend upon its
What is the correct answer?
4
X-rays are
D. Of higher wavelength than visible light
What is the correct answer?
4
On being hit with a hammer, __________ will readily fracture.
What is the correct answer?
4
Vernier calipers cannot be used to measure the
A. I.D. & O.D. of the shaft
D. Clearance between two mating surfaces
What is the correct answer?
4
Which of the following is preferred for riveting?
What is the correct answer?
4
Electrolytic reduction cell used for conversion of calcined Al2O3 to Al is a carbon lined furnace operating at 800-900 °C. The purpose of electric current supplied to the furnace is to
A. Achieve very high purity of aluminium (99.9%)
B. Keep the electrolyte in liquid condition by the generation of heat
C. Electrolytically dissociate alumina
What is the correct answer?
4
Annealing of white cast iron produces __________ iron.
What is the correct answer?
4
Iron content in Indian iron ore is about __________ percent.
What is the correct answer?
4
Constituents of stellite are
B. Cobalt, chromium & tungsten
C. Zinc, aluminium & nickel
D. Nickel, cobalt & vanadium
What is the correct answer?
4
Corrosion of metals cannot be prevented by its
What is the correct answer?
4
The material used for coating the welding electrode is termed as the
What is the correct answer?
4
__________ is the trade name assigned to a nonferrous cast alloy composed of cobalt, chromium & tungsten.
What is the correct answer?
4
Superheating of steam is done at constant
What is the correct answer?
4
A steam pipe is intended to be insulated with two layers of insulating materials of different thermal conductivities. For minimum heat transfer to take place
A. The better insulation material should be put just next to pipe (i.e., inside)
B. The better insulating material should be put outside
C. Either of the insulating material could be put on either side
D. Steam temperature is considered before deciding as to which insulating material is to be put inside (i.e., just next to the pipe)
What is the correct answer?
4
Screws are specified by their __________ diameters.
What is the correct answer?
4
Pressure required to increase the density of water by about 1% is __________ atmosphere.
What is the correct answer?
4
For an ideal gas, Cp - Cv is
What is the correct answer?
4
Window panes of aeroplanes are normally made of
C. Bakelite (phenol formaldehyde)
What is the correct answer?
4
Eutectic reaction for iron-carbon system occurs at a temperature of __________ °C.
What is the correct answer?
4
The bank of tubes located at the back of the domestic refrigerators are the __________ tubes.
What is the correct answer?
4
Potable water means the water used for
D. Evaporation to produce steam
What is the correct answer?
4
In case of brasses, with decreasing zinc percentage and increasing copper percentage, its __________ increases.
What is the correct answer?
4
Gas turbine normally employs a constant __________ cycle.
What is the correct answer?
4
A jig is used while __________ a hole.