Related Questions
What is the correct answer?
4
The malleability of a material is the property by virtue of which it can be rolled or hammered into thin sheets. Which of the following materials has the maximum malleability?
What is the correct answer?
4
Tempering of a material does not improve its
What is the correct answer?
4
The product out from a cupola is called
What is the correct answer?
4
Boiler draught of 10 mm water column is equivalent to
What is the correct answer?
4
The __________ of a double acting reciprocating pump as compared to the single acting pump will be almost double.
What is the correct answer?
4
Particle nature of cathode rays is proved due to the fact that they
A. Travel in a straight line
B. Get deflected by magnetic electric field
D. Heat the exposed material
What is the correct answer?
4
Which of the following are considered applications of ultrasonic testing?
A. Determination of elastic constant
B. Detection of defects in metal
C. Measurement of material thickness
What is the correct answer?
4
The thickness of oxide film is y at time t. If are the temperature dependent constants, the parabolic law of oxidation is given by
What is the correct answer?
4
Which of the following if present in iron ore, enhances its value?
What is the correct answer?
4
Steel & cast iron pipes are produced by __________ casting.
What is the correct answer?
4
In the X-ray radiography technique, the tube voltage for thicker plates as compared to thin plates, should be
A. Higher, as it gives higher wavelength
B. Lower, as it gives higher wavelength
C. Higher, as it gives shorter wavelength
D. Lower, as it gives shorter wavelength
What is the correct answer?
4
The only suitable method for hardening the low carbon steel is case hardening. Which of the following is a case hardening process?
What is the correct answer?
4
Diamagnetic materials
A. Are magnetised by eddy currents only
B. Are non-magnetic and cannot be magnetised
C. Are magnetised in direction opposite to the magnetic field
D. Can be magnetised in one direction only
What is the correct answer?
4
Which of the following materials does not form adherent oxide film on surface?
What is the correct answer?
4
Heating the Hypo-eutectoid steels to 30°C above the upper critical temperature line, soaking at that temperature and then cooling slowly to the room temperature to form a pearlite & ferrite structure is called
What is the correct answer?
4
Depreciation of machines fails under the indirect expenses head. As per income tax regulations, it is calculated by the __________ method.
C. Multiple straight line
D. Sum of the years digit
What is the correct answer?
4
Cold working of a material results in increase in hardness, which is termed as the __________ hardening.
What is the correct answer?
4
Runge-Kutta method is used to solve a/an
A. Ordinary differential equation of nth order
B. Simultaneous non-linear equation
C. Linear differential equation
What is the correct answer?
4
Maximum heat dissipation occurs from a steel wire (k = 0.5 W/m. k) of 15 mm diameter exposed to air (h = 20W/m2 .k), when the insulation thickness is __________ mm.
What is the correct answer?
4
Which of the following heat treatment processes is usually applied to castings?
What is the correct answer?
4
Methyl orange indicator turns
A. Orange yellow in alkaline medium
B. Orange yellow in acidic medium
C. Colourless in acidic medium
D. Colourless in basic medium
What is the correct answer?
4
Minimum temperature upto which water can be theoretically cooled down in the cooling tower by evaporative cooling is equal to the __________ temperature of air.
What is the correct answer?
4
Cold cracking in the heat affected zone of a high strength steel weld can take place because of the
C. Relatively high sulphur content in the base metal
D. Sufficient hydrogen present in the welding arc
What is the correct answer?
4
'Ice point' is designated on Fahrenheit temperature scale by
What is the correct answer?
4
The most serious manufacturing defect from fracture toughness point of view is
What is the correct answer?
4
Cobalt - 60 is used as a source of __________ in medical therapy & industrial radiography.
What is the correct answer?
4
Pick out the wrong statement about the machinability of metals. Machinability of a metal
A. Decreases with increase in strain hardening tendencies
B. Decreases with increase in hardness, in general
C. Depend on the composition, microstructure and physical & mechanical properties
D. Decreases with increases in tensile strength & decrease in grain size
What is the correct answer?
4
__________ is a non volatile film forming constituent of a paint.
What is the correct answer?
4
__________ has the highest melting point out of the following.
What is the correct answer?
4
In the formation of cermets, the ratio of ceramic material to metallic material is usually 80:20. Which of the following is a cermet?