Related Questions
What is the correct answer?
4
Fatigue limit improvement by over stressing the metal by successively increasing the load is called coaxing. In fatigue failure, the material fails
C. Below the elastic limit
What is the correct answer?
4
The product of a commercial direct reduction process is
D. Iron saturated with carbon
What is the correct answer?
4
Compressed dry air is used as the cutting fluid, while machining
What is the correct answer?
4
Resistance of an electrical conductor is proportional to its (where, l = length and A = cross-sectional area of the conductor)
What is the correct answer?
4
__________ is the most important element, which controls the physical properties of steel.
What is the correct answer?
4
__________ has the highest melting point out of the following.
What is the correct answer?
4
Tumbling is the process of improving the __________ of the materials/parts.
What is the correct answer?
4
Metal cutting by oxy-acetylene flame is accomplished by the __________ of the metal.
What is the correct answer?
4
Lead pencil contains
What is the correct answer?
4
Hot extrusion process is not used for making
A. Cast iron pipe for domestic water supply
B. Aluminium curtain rods
C. Stainless steel tubes used in furnitures
What is the correct answer?
4
Vibration upto 100 kilo hertz can be most accurately measured by a __________ type accelerometer.
What is the correct answer?
4
Pearlite comprises of
A. 87% cementite & 13% Fe
B. 87% ferrite & 13% cementite
C. 93.33% ferrite & 6.67% C
What is the correct answer?
4
The temperature at which ferromagnetic material can no longer be magnetised by the outside forces, is termed as the
What is the correct answer?
4
Cemented carbide tools are not suitable for cutting
What is the correct answer?
4
A pycnometer is used for the measurement of
A. Flow rate of molten metal
B. Specific gravity of a liquid
D. Concentration of a solution
What is the correct answer?
4
__________ is the trade name assigned to a nonferrous cast alloy composed of cobalt, chromium & tungsten.
What is the correct answer?
4
When an isolated thermodynamic system executes a process,
B. Heat transfer takes place
C. Mass flow occurs across the boundary of the system
D. No chemical reaction takes place within the system
What is the correct answer?
4
Density in the solid state is slightly less than that in its liquid state, in case of
What is the correct answer?
4
The lightest non-inflammable gas is
What is the correct answer?
4
Though tin occurs lower than iron in the electrochemical series, yet it is coated on steel for corrosion protection, because of its
C. Resistance to vegetable acids as the tin plate are commercially used in 'canning' industry
What is the correct answer?
4
Brass parts with high residual tensile stress at the surface are susceptible to season cracking (i.e. spontaneous cracking occuring on exposure to atmospheric corrosion), if its zinc percentage is more than
What is the correct answer?
4
The property of material, by which a given amount of energy is absorbed by it without plastic deformation, is called the
What is the correct answer?
4
Pick out the correct combination about the role of various additives used in polymers.
A. Plasticiser: increases the polymer strength
B. Heat stabiliser: increases the maximum service temperature
C. Fillers: Does not affect the property of polymer but increases its weight
D. Lubricants: increases the flexibility of polymers
What is the correct answer?
4
In a counter flow heat exchanger, hot fluid enters at 170°C & leaves at 150°C, while the cold fluid enters at 50°C & leaves at 70°C. The arithmetic mean temperature difference in this case is __________ °C.
What is the correct answer?
4
In condensers used in thermal power plants, steam is normally used in shell side and cooling water on the tube side, because of the reason that
A. Compared to the mass flow rate of cooling water, the rate of condensation of steam is invariably smaller
B. Maintaining vacuum on tube side is more difficult than that on the shell side
C. Water velocity can be increased conveniently to increase the overall heat transfer co-efficient because of its lower specific volume compared to steam
D. Condenser can act as a storage unit for condensed steam
What is the correct answer?
4
For infinite parallel planes having emissivities ε1 & ε2, the interchange factor for radiation from surface 1 to surface 2 is given by
What is the correct answer?
4
Ultimate strength in tension as compared to that in shear for steel is
What is the correct answer?
4
Nuclear fission of one atom of uranium-235 produces the energy equivalent to about __________ MeV.
What is the correct answer?
4
Normalising of a casting does not
B. Refine its grain structure
D. Improve its mechanical properties
What is the correct answer?
4
Thermal conductivity of a material does not depend upon its