The normal stress is the same in all directions at a point in a fluid, only when the fluid

Question

The normal stress is the same in all directions at a point in a fluid, only when the fluid

A. Is at rest & has zero viscosity

B. Is frictionless

C. Fluid layer has no motion relative to an adjacent layer of fluid

D. is incompressible & frictionless

Share this question with your friends

Show all Chemical Engineering Basics MCQ

Comment

In the formation of cermets, the ratio of ceramic material to metallic material is usually 80:20. Which of the following is a cermet?

A. Zirconia

B. Alumina

C. Bakelite

D. Tungsten carbide

Discuss this answer

Which of the following is not a principal alloying element for the structural steel?

A. Molybdenum

B. Nickel

C. Manganese

D. Chromium

Discuss this answer

Laser welding is widely employed in the __________ industries.

A. Electronic

B. Structural

C. Process

D. Heavy

Discuss this answer

__________ glass is used in the mercury in glass thermometer meant for measuring a temperature of 500°C.

A. Borosilicate

B. High silica

C. Supermax

D. Lead

Discuss this answer

The activity co-efficient of the solute in a dilute solution

A. Decreases with the increase of concentration of the solute

B. Increases with the increase of concentration of the solute

C. Remains constant

D. Is unity at infinite dilution

Discuss this answer

Venturimeter is used to measure the flow rate of fluids in pipes, when the pipe is in __________ position.

A. Horizontal

B. Vertical

C. Inclined

D. Any

Discuss this answer

Copper deposits are found in India at the following location:

A. Kudremukh

B. Kolar

C. Khetri

D. Ramagundam

Discuss this answer

What is the value of entropy at 273°K?

A. 0

B. 1

C. ∞

D. None of these

Discuss this answer

A material being tested for endurance strength is subjected to the __________ load.

A. Impact

B. Completely reversed

C. Dynamic

D. Static & dynamic

Discuss this answer

Atomic __________ of an element is a whole number.

A. Weight

B. Number

C. Volume

D. Radius

Discuss this answer

Which of the following can be manufactured using powder metallurgy techniques?

A. Brake linings

B. Bearings

C. Carbide tool tips

D. All 'a', 'b' and 'c'

Discuss this answer

The main charge in blast furnace is usually

A. Iron ore & coke

B. Iron ore, coke & air

C. Limestone, coke & iron ore

D. Limestone, sand & iron ore

Discuss this answer

The fugacity of liquid water at 298 K is approximately 3171 P_a. Considering the ideal heat of vaporisation as 43723 J/gm.mole, its fugacity at 300 K would be

A. 3171P_a

B. 3567P_a

C. 1.01 × 10⁵P_a

D. 5000P_a

Discuss this answer

An approximately __________ process exemplifies the flow of a gas through a very long pipe of uniform cross-section.

A. Adiabatic

B. Isothermal

C. Isentropic

D. Isochoric

Discuss this answer

When the wavelength of incident X-rays increases, the angle of diffraction

A. Decreases

B. Increases

C. Remain constant

D. Shows no systematic variation

Discuss this answer

The __________ of a double acting reciprocating pump as compared to the single acting pump will be almost double.

A. Flow output

B. Head developed

C. Overall efficiency

D. Weight

Discuss this answer

Which of the following forces does not act on a fluid at rest?

A. Viscous force

B. Gravity force

C. Hydrostatic force

D. Surface tension force

Discuss this answer

At absolute zero temperature, for any reaction involving condensed phases

A. Δ G° = 0 , Δ H° = 0

B. Δ H° = 0 , Δ S° = 0

C. Δ S° = 0 , Δ E° = 0

D. Δ S° = 0 , Δ Cp° = 0

Discuss this answer

Cast iron contains __________ percent carbon.

A. 2.5

B. 3.75

C. 4.75

D. 5.25

Discuss this answer

__________ is not used as a material of construction in thermocouples.

A. Alumel

B. Rhodium

C. Constantan

D. Duralumin

Discuss this answer

Which of the following is the most suitable material of construction for the condenser tubes, where the cooling medium is brine (salty water)?

A. Aluminium

B. Copper

C. Titanium

D. Stainless steel

Discuss this answer

The excess air required for the combustion of pulverised coal is of the order of about __________ percent.

A. 5

B. 15

C. 30

D. 45

Discuss this answer

Which of the following is not an ore of copper?

A. Cryolite

B. Azurite

C. Chalcopyrite

D. Malachite

Discuss this answer

Dryness factor of steam is defined as the ratio of the mass of vapor in the mixture to the mass of the mixture. Dryness factor of steam is measured by a __________ calorimeter.

A. Bomb

B. Throttling

C. Junker's

D. Boy's

Discuss this answer

The amount of water evaporated in kg per kg of fuel burnt in a boiler is called the __________ of a boiler.

A. Evaporative capacity

B. Evaporation efficiency

C. Thermal efficiency

D. Steam load

Discuss this answer

Which of the following is the most wear resistant grade of carbide used for the cutting tools?

A. Aluminium carbide

B. Tungsten carbide

C. Nickel carbide

D. Iron carbide

Discuss this answer

The noble metals

A. Are exemplified by Na, K and Li

B. Do not resist corrosion very strongly

C. Are the lowermost in the electro-chemical series of metals

D. None of these

Discuss this answer

Consideration of the creep is the most important in case of the

A. Blades of gas turbine

B. Piston of an I. C. engine

C. Flywheel of steam engine

D. Cycle chain

Discuss this answer

Tin based white metals are used, where bearings are subjected to

A. High pressure & load

B. Low pressure & load

C. High temperature

D. Large surface wear

Discuss this answer

Two wires of the same radius & material having length in the ratio of 1 : 2 are stretched by the same force. The strain produced in the two wires will be in the ratio of

A. 1 : 1

B. 1 : 2

C. 2 : 1

D. 1 : 4

Discuss this answer

Accepted Answer

D. is incompressible & frictionless

The normal stress is the same in all directions at a point in a fluid, only when the fluid

Correct Answer :

Show all Chemical Engineering Basics MCQ

Related Questions

In the formation of cermets, the ratio of ceramic material to metallic material is usually 80:20. Which of the following is a cermet?

Which of the following is not a principal alloying element for the structural steel?

Laser welding is widely employed in the __________ industries.

__________ glass is used in the mercury in glass thermometer meant for measuring a temperature of 500°C.

The activity co-efficient of the solute in a dilute solution

Venturimeter is used to measure the flow rate of fluids in pipes, when the pipe is in __________ position.

Copper deposits are found in India at the following location:

What is the value of entropy at 273°K?

A material being tested for endurance strength is subjected to the __________ load.

Atomic __________ of an element is a whole number.

Which of the following can be manufactured using powder metallurgy techniques?

The main charge in blast furnace is usually

The fugacity of liquid water at 298 K is approximately 3171 P_a. Considering the ideal heat of vaporisation as 43723 J/gm.mole, its fugacity at 300 K would be

An approximately __________ process exemplifies the flow of a gas through a very long pipe of uniform cross-section.

When the wavelength of incident X-rays increases, the angle of diffraction

The __________ of a double acting reciprocating pump as compared to the single acting pump will be almost double.

Which of the following forces does not act on a fluid at rest?

At absolute zero temperature, for any reaction involving condensed phases

Cast iron contains __________ percent carbon.

__________ is not used as a material of construction in thermocouples.

Which of the following is the most suitable material of construction for the condenser tubes, where the cooling medium is brine (salty water)?

The excess air required for the combustion of pulverised coal is of the order of about __________ percent.

Which of the following is not an ore of copper?

Dryness factor of steam is defined as the ratio of the mass of vapor in the mixture to the mass of the mixture. Dryness factor of steam is measured by a __________ calorimeter.

The amount of water evaporated in kg per kg of fuel burnt in a boiler is called the __________ of a boiler.

Which of the following is the most wear resistant grade of carbide used for the cutting tools?

The noble metals

Consideration of the creep is the most important in case of the

Tin based white metals are used, where bearings are subjected to

Two wires of the same radius & material having length in the ratio of 1 : 2 are stretched by the same force. The strain produced in the two wires will be in the ratio of

Also checkout

The normal stress is the same in all directions at a point in a fluid, only when the fluid

Correct Answer :

Show all Chemical Engineering Basics MCQ

Related Questions

In the formation of cermets, the ratio of ceramic material to metallic material is usually 80:20. Which of the following is a cermet?

Which of the following is not a principal alloying element for the structural steel?

Laser welding is widely employed in the __________ industries.

__________ glass is used in the mercury in glass thermometer meant for measuring a temperature of 500°C.

The activity co-efficient of the solute in a dilute solution

Venturimeter is used to measure the flow rate of fluids in pipes, when the pipe is in __________ position.

Copper deposits are found in India at the following location:

What is the value of entropy at 273°K?

A material being tested for endurance strength is subjected to the __________ load.

Atomic __________ of an element is a whole number.

Which of the following can be manufactured using powder metallurgy techniques?

The main charge in blast furnace is usually

The fugacity of liquid water at 298 K is approximately 3171 Pa. Considering the ideal heat of vaporisation as 43723 J/gm.mole, its fugacity at 300 K would be

An approximately __________ process exemplifies the flow of a gas through a very long pipe of uniform cross-section.

When the wavelength of incident X-rays increases, the angle of diffraction

The __________ of a double acting reciprocating pump as compared to the single acting pump will be almost double.

Which of the following forces does not act on a fluid at rest?

At absolute zero temperature, for any reaction involving condensed phases

Cast iron contains __________ percent carbon.

__________ is not used as a material of construction in thermocouples.

Which of the following is the most suitable material of construction for the condenser tubes, where the cooling medium is brine (salty water)?

The excess air required for the combustion of pulverised coal is of the order of about __________ percent.

Which of the following is not an ore of copper?

Dryness factor of steam is defined as the ratio of the mass of vapor in the mixture to the mass of the mixture. Dryness factor of steam is measured by a __________ calorimeter.

The amount of water evaporated in kg per kg of fuel burnt in a boiler is called the __________ of a boiler.

Which of the following is the most wear resistant grade of carbide used for the cutting tools?

The noble metals

Consideration of the creep is the most important in case of the

Tin based white metals are used, where bearings are subjected to

Two wires of the same radius & material having length in the ratio of 1 : 2 are stretched by the same force. The strain produced in the two wires will be in the ratio of

Also checkout

The fugacity of liquid water at 298 K is approximately 3171 P_a. Considering the ideal heat of vaporisation as 43723 J/gm.mole, its fugacity at 300 K would be