Related Questions
What is the correct answer?
4
In chemical dehumidification of air
A. Both specific humidity & dry bulb temperature increases
B. Both specific humidity & dry bulb temperature decreases
C. Specific humidity decreases & dry bulb temperature increases
D. Specific humidity increases & dry bulb temperature decreases
What is the correct answer?
4
If the head is doubled in & centrifugal pump, the power required will increase in the ratio of
What is the correct answer?
4
More than 95% of __________ is present in corundum.
What is the correct answer?
4
With increase in impurities in metals, their corrosion resistances
D. May increase or decrease; depending on the type of metal
What is the correct answer?
4
According to maximum shear stress failure criterion, yielding in material occurs, when the maximum shear stress is equal to __________ times the yield stress.
What is the correct answer?
4
Dew point temperature always gives an indication of the __________ of the moist air.
What is the correct answer?
4
Brinell Hardness Number (BHN) for talc is approximately in the range of
What is the correct answer?
4
A spring material should have low
What is the correct answer?
4
Carbon supply in pack carburising process is in the form of
What is the correct answer?
4
The ratio of thermal & electrical conductivity is same for all the metals at the same temperature; and at around room temperature, this ratio is proportional to(where, T = absolute temperature, °K)
What is the correct answer?
4
Energy to be supplied to the radioactive nucleus for the emission of a neutron is __________ MeV.
What is the correct answer?
4
Oxygen cylinders used for autogenous (cutting/welding) purposes are
A. Seamless & made of steel
B. Heat treated before use
D. Welded steel cylinders
What is the correct answer?
4
Which of the following is resistant to the action of both heat & chemicals?
What is the correct answer?
4
As per the Indian boiler regulation (IBR), the type of joint preferred for the circumferential joint is the __________ joint.
What is the correct answer?
4
__________ is the most suitable lubricant for drawing mild steel wires?
What is the correct answer?
4
Fibre glass is a composite material of
A. Glass fibre in a polymer matrix
B. Glass fibre in a metallic matrix
C. Polymer fibre in a glassy matrix
What is the correct answer?
4
Which of the following phenomenon/ phenomena is/are diffusion controlled?
What is the correct answer?
4
The best guide to judge the general quality of water is the measurement of its
B. Electrical conductivity
D. Dissolved oxygen content
What is the correct answer?
4
__________ is not used as a material of construction in thermocouples.
What is the correct answer?
4
Annealing of cast iron
A. Softens it to facilitate machining
B. Decreases the free carbon
C. Increases the strength
What is the correct answer?
4
Which of the following processes follows the hardening process for reducing the hardening strains & increasing the toughness of the steel part?
What is the correct answer?
4
Drills are usually made of
What is the correct answer?
4
Potable water means the water used for
D. Evaporation to produce steam
What is the correct answer?
4
In the blast furnace, incorporation of water vapour in the blast gives the following effect.
A. Increases the reducing potential of the gas
B. Increases the flame temperature
C. No significant change occurs
D. Increases the hydrogen content in the metal
What is the correct answer?
4
Absolute zero, pressure will occur, when the molecular momentum of the system becomes zero. A liquid will cease to exist as liquid at
What is the correct answer?
4
The ratio of the shear stress to the principal stress on a principal plane is
What is the correct answer?
4
The yield point phenomenon observed in annealed low carbon steel is due to the presence of the following element.
What is the correct answer?
4
Wohler test is a destructive test to find out the __________ strength of a prepared metal specimen.
What is the correct answer?
4
Steel rods are normally used for concrete reinforcement because concrete and steel have almost equal
D. Thermal co-efficient of expansion
What is the correct answer?
4
Strain hardening effect in metals subjected to cold working is due to the __________ mechanism.