Related Questions
What is the correct answer?
4
I.S. specifies following total number of grades of tolerances
What is the correct answer?
4
The coefficient of friction in belt drive depends upon
C. Materials of belt and pulley
What is the correct answer?
4
For tight leakage joints, following type of thread is best suited
D. NPT (national pipe threads)
What is the correct answer?
4
In the calculation of induced shear stress in helical springs, the Wahl's stress factor is used to take care of
A. Combined effect of transverse shear stress and bending stress in the wire
B. Combined effect of bending stress and curvature of the wire
C. Combined effect of transverse shear stress and curvature of wire
D. Combined effect of torsional shear stress and transverse shear stress in the wire
What is the correct answer?
4
The notch sensitivity q is expressed in terms of fatigue stress concentration factor Kf and theoretical stress concentration factor Kt as
What is the correct answer?
4
Which of the following is not correct procedure to increase the fatigue limit?
C. Surface decarburisation
What is the correct answer?
4
The permissible stress in the fillet weld is 100 N/mm². The fillet weld has equal leg lengths of 15 mm each. The allowable shearing load on the weldment per cm length of the weld is
What is the correct answer?
4
In a belt drive, if the pulley diameter is doubled keeping the tension and belt width constant, then it will be necessary to
A. Increase the key length
B. Increase the key depth
C. Increase the key width
D. Decrease the key length
What is the correct answer?
4
The suitable material for belt used in flour mill is
What is the correct answer?
4
Eulers formula for a mild steel column is not valid if the slenderness ratio is
What is the correct answer?
4
The circumferential and longitudinal strains in a cylindrical boiler under internal steam pressure are εc and εl respectively. The change in volume of the boiler cylinder per unit volume will be
What is the correct answer?
4
An Involute pinion and gear are in mesh. If both have the same size of addendum, then there will be interference between the
A. Tip of the pinion and flank of gear
B. Tip of the gear and flank of pinion
C. Flanks of both gear and pinion
D. Tip of both gear and pinion
What is the correct answer?
4
A stud
A. Has a head on one end and a nut fitted to the other
B. Has head at one end and other end fits into a tapped hole in the other part to be joined
C. Has both the ends threaded
What is the correct answer?
4
The bearings of heavy series have capacity ________ over the medium series.
What is the correct answer?
4
Stress concentration in cyclic loading is more serious in
C. Equally serious in both cases
D. Depends on other factors
What is the correct answer?
4
The initial tension (in newtons) in a bolt used for making a fluid tight joint like steam engine cover joints, is calculated by the relation (where d = Nominal diameter of bolt in mm)
What is the correct answer?
4
Two helical springs of the same material and of equal circular crosssection, length and number of turns, but having radii 80 mm and 40 mm, kept concentrically (smaller radius spring within the larger radius spring), are compressed between two parallel planes with a load W. The inner spring will carry a load equal to
What is the correct answer?
4
According to I.B.R., when the thickness of the boiler shell (t) is less than 8 mm, then the diameter of the rivet hole (d) is obtained by
A. Equating tearing resistance of the plate to the shearing resistance of the rivets
B. Equating tearing resistance of the plate to the crushing resistance of the rivets
C. Equating shearing resistance to the crushing resistance of the rivets
What is the correct answer?
4
According to Indian standards, total numbers of fundamental deviations are
What is the correct answer?
4
When a hole of diameter d is punched in a metal of thickness 't', then the force required to punch a hole is equal to (where τu = Ultimate shear strength of the material of the plate)
What is the correct answer?
4
The face of the tooth is the
A. Surface of the top of the tooth
B. Surface of the tooth above the pitch surface
C. Surface of the tooth below the pitch surface
D. Width of the tooth measured along the pitch circle
What is the correct answer?
4
At low temperatures (say 75°C) the notched bar impact value of steel
D. Depends on heat treatment carried out
What is the correct answer?
4
Fabric belts are used in industrial applications because
B. They can work at high temperature
C. They are unaffected by moisture and humidity
What is the correct answer?
4
Machine screws are
A. Similar to small size tap bolts except that a greater variety of shapes of heads are available
B. Slotted for a screw driver and generally used with a nut
C. Used to prevent relative motion between two parts
What is the correct answer?
4
In designing thick cylinders, the equation used is
What is the correct answer?
4
Gear box is used
C. To obtain variable speeds
D. To increase efficiency of system
What is the correct answer?
4
In helical gears, the distance between similar faces of adjacent teeth along a helix on the pitch cylinders normal to the teeth, is called
What is the correct answer?
4
Whether any core is required in wire ropes
What is the correct answer?
4
The ratio of the ultimate stress to the design stress is known as
What is the correct answer?
4
According to Indian standards, total numbers of tolerance grades are