Home
Current Affairs January 2024

What is the correct answer?

4

The radius of the Mohrs circle in the given figure is equal to

A. Sum of two principal stresses

B. Difference of two principal stresses

C. Half the sum of two principal stresses

D. Half the difference of two principal stresses

Correct Answer :

D. Half the difference of two principal stresses


Related Questions

What is the correct answer?

4

For a perfect gas, according to Boyle's law (where p = Absolute pressure, v = Volume, and T = Absolute temperature)

A. p v = constant, if T is kept constant

B. v/T = constant, if p is kept constant

C. p/T = constant, if v is kept constant

D. T/p = constant, if v is kept constant

What is the correct answer?

4

Which of the following has the highest calorific value?

A. Peat

B. Lignite

C. Bituminous coal

D. Anthracite coal

What is the correct answer?

4

Reversed joule cycle is called

A. Carnot cycle

B. Rankine cycle

C. Brayton cycle

D. Bell Coleman cycle

What is the correct answer?

4

The relation between equivalent length (L) and actual length (l) of a column for both ends fixed is

A. L = l/2

B. L = l/√2

C. L = l

D. L = 2l

What is the correct answer?

4

The cycle in which heat is supplied at constant volume and rejected at constant pressure is known as

A. Dual combustion cycle

B. Diesel cycle

C. Atkinson cycle

D. Rankine cycle

What is the correct answer?

4

A beam which is fixed at one end and free at the other is called

A. Simply supported beam

B. Fixed beam

C. Overhanging beam

D. Cantilever beam

What is the correct answer?

4

Workdone during adiabatic expansion is given by (where p1 v1, T1 = Pressure, volume and temperature for the initial condition of gas, p2, v2, T2 = Corresponding values for the final condition of gas, R = Gas constant, and γ = Ratio of specific heats)

A. (p1 v1 - p2 v2)/(γ - 1)

B. [m R (T1 - T2)] /(γ - 1)

C. [m R T1/(γ - 1)][1 - (p2 v2 /p1 v1)]

D. All of these

What is the correct answer?

4

Diesel cycle consists of __________ processes.

A. Two constant volume and two isentropic

B. Two constant pressure and two isentropic

C. Two constant volume and two isothermal

D. One constant pressure, one constant volume and two isentropic

What is the correct answer?

4

The property of a working substance which increases or decreases as the heat is supplied or removed in a reversible manner, is known as

A. Enthalpy

B. Internal energy

C. Entropy

D. External energy

What is the correct answer?

4

The ideal efficiency of a Brayton cycle with regeneration, with increase in pressure ratio will

A. Increase

B. Decrease

C. Remain unchanged

D. Increase/decrease depending on application

What is the correct answer?

4

The calorific value of gaseous fuel is expressed in

A. kJ

B. kJ/kg

C. kJ/m2

D. kJ/m3

What is the correct answer?

4

When the gas is heated at constant pressure, the heat supplied

A. Increases the internal energy of the gas

B. Increases the temperature of the gas

C. Does some external work during expansion

D. Both (B) and (C)

What is the correct answer?

4

One kg of carbon monoxide requires _______kg of oxygen to produce 11/7 kg of carbon dioxide gas.

A. 11/7

B. 9/7

C. 4/7

D. All of the above

What is the correct answer?

4

In order to prevent crushing of masonry at the base of the dam, the maximum stress should be __________ the permissible stress of the soil.

A. Equal to

B. Less than

C. More than

D. None of these

What is the correct answer?

4

The total energy of a molecule is shared equally by the various degrees of freedom possessed by it. This law is known as

A. Law of equipartition of energy

B. Law of conservation of energy

C. Law of degradation of energy

D. None of these

What is the correct answer?

4

Efficiency of a riveted joint is the ratio of its strength (max. load it can resist without failure) to the strength of the un-punched plate in

A. Tension

B. Compression

C. Bearing

D. Any one of the above

What is the correct answer?

4

The neutral axis of the cross-section a beam is that axis at which the bending stress is

A. Zero

B. Minimum

C. Maximum

D. Infinity

What is the correct answer?

4

The ratio of the largest load in a test to the original cross-sectional area of the test piece is called

A. Elastic limit

B. Yield stress

C. Ultimate stress

D. Breaking stress

What is the correct answer?

4

When a body is subjected to two equal and opposite pushes, as a result of which the body tends to reduce its length, then

A. The stress and strain induced is compressive

B. The stress and strain induced is tensile

C. Both A and B is correct

D. None of these

What is the correct answer?

4

The bending stress in a beam is _________ section modulus.

A. Inversely proportional to two times

B. Directly proportional to

C. Inversely proportional to

D. None of these

What is the correct answer?

4

The natural solid fuel is

A. Wood

B. Coke

C. Anthracite coal

D. Pulverised coal

What is the correct answer?

4

The amount of heat required to raise the temperature of the unit mass of gas through one degree at constant volume, is called

A. Specific heat at constant volume

B. Specific heat at constant pressure

C. Kilo Joule

D. None of these

What is the correct answer?

4

A double strap butt joint with equal straps is

A. Always in single shear

B. Always in double shear

C. Either in single shear or double shear

D. None of these

What is the correct answer?

4

A steel bar of 5 mm is heated from 25°C to 45°C and it is free to expand. The bar will induce

A. No stress

B. Shear stress

C. Tensile stress

D. Compressive stress

What is the correct answer?

4

First law of thermodynamics deals with

A. Conservation of heat

B. Conservation of momentum

C. Conservation of mass

D. Conservation of energy

What is the correct answer?

4

Which of the following gas has a minimum molecular mass?

A. Oxygen

B. Nitrogen

C. Hydrogen

D. Methane

What is the correct answer?

4

The shear force diagram for a simply supported beam carrying a uniformly distributed load of w per unit length, consists of

A. One right angled triangle

B. Two right angled triangles

C. One equilateral triangle

D. Two equilateral triangles

What is the correct answer?

4

For a simply supported beam of length l, when a concentrated load W is applied in the centre of the beam, the maximum deflection is

A. 5WL³/ 384EI

B. WL³/384EI

C. WL³/ 348EI

D. WL³/ 48EI

What is the correct answer?

4

The buckling load for a given material depends on

A. Slenderness ratio and area of cross-section

B. Poisson's ratio and modulus of elasticity

C. Slenderness ratio and modulus of elasticity

D. Slenderness ratio, area of cross-section and modulus of elasticity

What is the correct answer?

4

If in the equation pvn = C, the value of n = ∝, then the process is called

A. Constant volume process

B. Adiabatic process

C. Constant pressure process

D. Isothermal process