The ratio of driving tensions for flat belts, neglecting centrifugal tension, is (where T₁, and T₂ = Tensions on the tight and slack sides of belt respectively, μ = Coefficient of friction, between the belt and pulley, and θ = Angle of contact)
T₁/T₂ = μθ
log (T₁/T₂) = μθ
T₁/T₂ =eμθ
T₁/T₂ = log μθ
Correct Answer :
C. T₁/T₂ =eμθ
Related Questions
If P1 and P2 are the tight and slack side tensions in the belt, then the initial tension Pi (neglecting centrifugal tension) will be equal to
P1 - P2
P1 + P2
2 × (P1 + P2)
[2 × (P1 + P2)] + Pc Where Pc is centrifugal tension
In nitrated parts, the origins of the fatigue cracks will occur at
Surface
Just below the surface
Within the core
None of the above
The helix angle for double helical gears may be made up to
45°
60°
75°
90°
The strap end of a connecting rod of steam engine is joined by
Gib of cotter joint
Sleeve and cotter joint
Spigot socket cotter joint
Knuckle joint
The shock absorbing capacity of a bolt can be increased by
Tightening it properly
Increasing shank diameter
Grinding the shank
Making shank diameter equal to core diameter of thread.
Crowning on pulley helps
In decreasing the slip of the belt
In increasing the slip of the belt
To keep the belt in centre on a pulley while it is in motion
To increase pulley life
The included angle in unified of American National threads is
60°
55°
47°
29°
If a spring is cut down into two springs, the stiffness of cut springs will be
Half
Same
Double
None of the above
The centre to centre distance between two consecutive rivets in a row, is called
Margin
Pitch
Back pitch
Diagonal pitch
The radial distance of a tooth from the pitch circle to the top of the tooth is called
Addendum
Dedendum
Clearance
Working depth
Turn buckle has
Right hand threads on bout ends
Left hand threads on both ends
Left hand threads on one end and right hand threads on other end
No threads
When the bolt is very yielding as compared to the connected members, then the resultant load on the bolt will be equal to the
Initial tension
External load applied
Sum of the initial tension and external load applied
Initial tension or external load, whichever is greater
In replacing the V-belts, a complete set of new belts is used instead of replacing a single damaged belt because
Belts are available in sets
Only one belt cannot be fitted with other used belts
The new belt will carry more than its share and result in short life
New and old belts will cause vibrations
The load cup of a screw jack is made separate from the head of the spindle to
Prevent the rotation of load being lifted
Enhance the load carrying capacity of the jack
Reduce the effort needed for lifting the working load
Reduce the value of frictional torque
A special case of ductility which permits materials to be rolled or hammered into thin sheets, is called
Plasticity
Elasticity
Ductility
Malleability
The yield point in static loading is __________ as compared to fatigue loading.
Higher
Lower
Same
None of these
In order to remove internal stresses produced by hardening the steel, the process usually adopted is
Tempering
Normalising
Annealing
Spheroidising
In the assembly of pulley, key and shaft
Pulley is made the weakest
Key is made the weakest
Key is made the strongest
All the three are designed for equal strength
Resilience of a material is important, when it is subjected to
Combined loading
Fatigue
Thermal stresses
Shock loading
A localised compressive stress at the area of contact between two members is known as
Tensile stress
Bending stress
Bearing stress
Shear stress
The period during which the cam follower remains at rest, when cam moves, is known as
Constant period
Fixed period
Dwell period
Idle period
The bearings of heavy series have capacity ________ over the medium series.
20 to 30%
10 to 20%
30 to 40%
40 to 50%
The pipe joint mostly used for pipes carrying water at low pressures is
Socket joint
Nipple joint
Union joint
Spigot and socket joint
Which of the following statement is correct?
The distance from a point on one thread to the corresponding point on the next thread is called pitch
The distance which a screw thread advances axially in one rotation of the nut is called lead
In single start threads, lead is equal to pitch
All of the above
Fibrous fracture occurs in
Ductile material
Brittle material
Elastic material
Hard material
According to Indian standards, total numbers of tolerance grades are
8
12
18
20
The expression 0.175 - 0.841/T is the Lewis form factor for
14 ½° composite and full depth involute system
20° full depth involute system
20° stub system
None of the above
Stress concentration is caused due to
Variations in load acting on a member
Variations in properties of materials in a member
Abrupt change of cross-section
All of these
Which of the following property is essential for spring materials?
Stiffness
Ductility
Resilience
Plasticity
Oil in journal bearing should be applied at the point where load is
Nil or lightest
Maximum
Average
Any one of the above