Home
Current Affairs January 2024

What is the correct answer?

4

The ratio of pitch circle diameter in millimetres to the number of teeth, is called

A. Circular pitch

B. Diametral pitch

C. Module

D. None of these

Correct Answer :

C. Module


Related Questions

What is the correct answer?

4

For a shaft diameter of 100 mm, the number of bolts in a flange coupling should be

A. 4

B. 6

C. 8

D. 10

What is the correct answer?

4

In radial bearings, the load acts __________ to the axis of rotation.

A. Parallel

B. Perpendicular

C. Both A and B

D. None of these

What is the correct answer?

4

The shearing stresses in the inner face as compared to outer face of the wire in a heavy close coiled spring is

A. Larger

B. Smaller

C. Equal

D. Larger/smaller depending on diameter of spring coil

What is the correct answer?

4

Endurance limit or fatigue limit is the maximum stress that a member can withstand for an infinite number of load applications without failure when subjected to

A. Dynamic loading

B. Static loading

C. Combined static and dynamic loading

D. Completely reversed loading

What is the correct answer?

4

When two springs are in series (having stiffness K), the equivalent stiffness will be

A. K

B. K/2

C. 2K

D. K/4

What is the correct answer?

4

The ultimate strength of steel in tension in comparison to shear is in the ratio of

A. 1 : 1

B. 2 : 1

C. 3 : 2

D. 2 : 3

What is the correct answer?

4

Aircraft body is usually fabricated by

A. Welding

B. Pre-casting

C. Riveting

D. Casting

What is the correct answer?

4

A taper key which fits half in the key way of the hub and half in the key way of shaft, is known as

A. Angular bevel gears

B. Mitre gears

C. Crown Bevel gears

D. Internal bevel gears

What is the correct answer?

4

The resilience of a bolt may be increased by

A. Increasing its shank diameter

B. Increasing its length

C. Decreasing its shank diameter

D. Decreasing its length

What is the correct answer?

4

Allen bolts are

A. Self locking bolts

B. Designed for shock load

C. Used in aircraft application

D. Provided with hexagonal depression in head

What is the correct answer?

4

The power transmitted by belt drive depends upon

A. Belt velocity

B. Initial belt tension

C. Arc of contact

D. All of the above

What is the correct answer?

4

For hardening alloy steels and high speed steels, they are heated to

A. 1100 to 1300°C

B. 1300 to 1500°C

C. 500 to 600°C

D. 700 to 900°C

What is the correct answer?

4

The modulus of elasticity for mild steel is approximately equal to

A. 80 kN/mm²

B. 100 kN/mm²

C. 110 kN/mm²

D. 210 kN/mm²

What is the correct answer?

4

The design of the pressure vessel is based on

A. Longitudinal stress

B. Hoop stress

C. Longitudinal and hoop stress

D. None of these

What is the correct answer?

4

Multiple threads are used to secure

A. Low efficiency

B. High efficiency

C. High load lifting capacity

D. High mechanical advantage

What is the correct answer?

4

In testing a material for endurance strength, it is subjected to

A. Static load

B. Dynamic load

C. Impact load

D. Completely reversed load

What is the correct answer?

4

Split nut is a locking device in which

A. One smaller nut is tightened over main nut and main nut tightened against smaller one by loosening, creating friction jamming

B. A slot is cut partly in middle of nut and then slot reduced by tightening screw

C. A hard fibre or nylon cotter is recessed in the nut and becomes threaded as the nut is screwed on the bolt causing a tight grip

D. Through slots are made at top and a cotter pin is passed through these and a hole in the bolt, and cotter pin splitted and bent in reverse direction at the other end

What is the correct answer?

4

For same pulley diameters, center distance, belt speed and belt and pulley materials,

A. Open belt drive transmits more power than crossed belt drive

B. Crossed belt drive transmits more power than open belt drive

C. Open and crossed belt drives transmit same power

D. Power transmission does not depend upon open and crossed types of constructions

What is the correct answer?

4

A localised compressive stress at the area of contact between two members is known as

A. Tensile stress

B. Bending stress

C. Bearing stress

D. Shear stress

What is the correct answer?

4

Jam nut is a locking device in which

A. One smaller nut is tightened over main nut and main nut tightened against smaller one by loosening, creating friction jamming

B. A slot is cut partly in middle of nut and then slot reduced by tightening a screw

C. A hard fibre or nylon cotter is recessed in the nut and becomes threaded as the nut is screwed on the bolt causing a tight grip

D. Through slots are made at top and a cotter pin is passed through these and a hole in the bolt, and cotter spitted and bent in reverse direction at other end

What is the correct answer?

4

The fatigue stress concentration factor is defined as

A. The ratio of endurance limit with stress concentration to the endurance limit without stress concentration

B. The ratio of endurance limit without stress concentration to the endurance limit with stress concentration

C. The product of the endurance limits with and without stress concentration

D. All of the above

What is the correct answer?

4

Cast iron pipes are mainly used

A. For conveying steam

B. In water and sewage systems

C. In pressure lubrication systems on prime movers

D. All of the above

What is the correct answer?

4

The resultant axial load on a bolt depends on

A. Initial tension

B. External load applied

C. Relative elastic yielding (springness) of the bolt and the connected member

D. All of the above

What is the correct answer?

4

In a partial journal bearing, the angle of contact of the bearing with the journal is

A. 120°

B. 180°

C. 270°

D. 360°

What is the correct answer?

4

Silver based solder is used for

A. Flaring

B. Brazing

C. Soft soldering

D. Fusion welding

What is the correct answer?

4

The product of the diametral pitch and circular pitch is equal to

A. 1

B. 1/π

C. π

D. π × number of teeth

What is the correct answer?

4

Which of the following statement is correct for gears?

A. The pitch circle diameter is equal to the product of module and number of teeth

B. The addendum is less than dedendum

C. The pitch circle is always greater than the base circle

D. All of the above

What is the correct answer?

4

The plasticity is the property of a material which enables it to

A. Regain its original shape after deformation when the external forces are removed

B. Draw into wires by the application of a tensile force

C. Resist fracture due to high impact loads

D. Retain deformation produced under load permanently

What is the correct answer?

4

The ratio of endurance limit in shear to the endurance limit in flexure is

A. 0.70

B. 0.25

C. 0.40

D. 0.55

What is the correct answer?

4

A machine part subjected to __________ is called a strut.

A. An axial compressive force

B. A tangential force

C. An axial tensile force

D. Any one of these