Related Questions
What is the correct answer?
4
VLSM allows you to summarize 192.168.2.0/24 and 192.168.3.0/24 as 192.168.2.0/25.
What is the correct answer?
4
You are given a Class C network, 192.168.1.0/24. You need one network with 120 hosts
and two networks with 60 hosts. How many subnet masks do you need?
What is the correct answer?
4
Which of the following is true concerning ISL?
A. It is supported on both the 1900 and 2950 switches.
B. It adds a 26-byte trailer and 4-byte header.
C. Tagging is done in software.
D. The original Ethernet frame is not modified.
What is the correct answer?
4
Which router command would you use to test only layer-3 connectivity?
What is the correct answer?
4
Which router command would you use to view the configuration register value?
What is the correct answer?
4
When examining the IP routing table, an EIGRP route will be shown as what letter?
What is the correct answer?
4
The _________ is your network equipment, which includes the DCE (e.g., a modem) and the DTE (e.g., a router).
What is the correct answer?
4
Which of the following is false concerning OSPF?
A. It provides a loop-free topology.
B. It is a classful protocol and allows for a hierarchical design.
C. It requires more memory and processing cycles than distance vector protocols.
D. It is complex to configure and difficult to troubleshoot.
What is the correct answer?
4
You are at User EXEC mode and type the letter e. What message appears?
C. % Unknown command or computer name
D. % Invalid input detected at '^'.
What is the correct answer?
4
Which 1900 command enables port security?
D. switchport port-security
What is the correct answer?
4
Which of the following are not features of ACLs?
A. Restricting telnet access to a router
B. Prioritizing WAN traffic
C. Filtering traffic from the router
D. Triggering dialup phone calls
What is the correct answer?
4
A ___________ is similar to a telephone circuit-switched connection.
What is the correct answer?
4
Ethernet ___________ has/have both a physical and logical bus topology.
D. 10BaseT, 10Base2, and 10Base5
What is the correct answer?
4
Which of the following is true concerning full-duplexing?
A. It can either send or receive frames, but not both simultaneously.
B. It can be used with hubs.
C. It can be used with 10Base5 cabling.
D. It uses point-to-point connections.
What is the correct answer?
4
EIGRP uses the _________ algorithm to update its routing table.
What is the correct answer?
4
When using debug with PAP, which of the following message types might you see?
What is the correct answer?
4
When using the show interfaces command, which Frame Relay information can you not see?
A. The DLCI number used for LMI
B. The number of LMIs sent and received
What is the correct answer?
4
You execute the line console 0 command from Configuration mode. What will the router's prompt be?
C. Router(config-interface)#
What is the correct answer?
4
Which of the following is true concerning bridges?
A. They switch frames in hardware.
B. They support half- and full-duplexing.
C. They support one collision domain for the entire bridge.
D. They do only store-and-forward switching.
What is the correct answer?
4
Which type of traffic is sent to a group of devices?
What is the correct answer?
4
Which command takes you from Privilege EXEC mode to User EXEC mode?
What is the correct answer?
4
You are given a Class B network with a subnet mask of 255.255.255.192. How many host
addresses are there on each subnet?
What is the correct answer?
4
Choose the following that a standard IP ACL can match on.
C. IP protocol information
What is the correct answer?
4
Frames sent above the __________ limit will have their _________ bit set.
What is the correct answer?
4
What would you enter to see the last few commands you entered?
What is the correct answer?
4
What command assigns a User EXEC password to a 2950 switch?
What is the correct answer?
4
How would you suspend a telnet session?
What is the correct answer?
4
Enter the wildcard mask value to match on every bit position in an address: _________.
What is the correct answer?
4
Distance vector protocols use ___________ to disseminate routing information.
What is the correct answer?
4
OSPF hellos are sent every __________ seconds on a multi-access medium.