Related Questions
What is the correct answer?
4
The relation between the pitch of the chain (p) and pitch circle diameter of the sprocket (D) is given by (where T = Number of teeth on the sprocket)
What is the correct answer?
4
A connecting rod is designed as a
What is the correct answer?
4
A taper key which fits half in the key way of the hub and half in the key way of shaft, is known as
What is the correct answer?
4
When a helical compression spring is cut into halves, the stiffness of the resulting spring will be
What is the correct answer?
4
When an open coiled helical compression spring is subjected to an axial compressive load, the stress induced in the wire is
What is the correct answer?
4
The difference between the tooth space and the tooth thickness as measured on the pitch circle, is called
What is the correct answer?
4
Auto frettage is the method of
A. Joining thick cylinders
B. Calculating stresses in thick cylinders
C. Pre-stressing thick cylinders
D. Increasing the life of thick cylinders
What is the correct answer?
4
A circular shaft can transmit a torque of 5 kN-m. If the torque is reduced to 4 kN-m, then the maximum value of bending moment that can be applied to the shaft is
What is the correct answer?
4
The radial distance of a tooth from the pitch circle to the top of the tooth is called
What is the correct answer?
4
The suitable material for belt used in flour mill is
What is the correct answer?
4
According to maximum shear stress theory, the maximum shear stress in the shaft is
C. (1/2) × [σ + √(σ² + 4τ²)]
What is the correct answer?
4
The objective of crowning of the flat pulleys of belt drive is to
A. Prevent the belt from running off the pulley
B. Increase the power transmission capacity
C. Increase the belt velocity
D. Prevent the belt joint from damaging the belt surface
What is the correct answer?
4
The standard length of the shaft is
What is the correct answer?
4
The material commonly used for crane hooks is
What is the correct answer?
4
The distribution of the forces along the length of key fitted in a shaft
C. Varies exponentially, being more near the torque-input end
D. Varies exponentially, being less near the torque-input end
What is the correct answer?
4
When compared to the rod of the same diameter and material, a wire rope
B. Has a much smaller load carrying capacity
C. Does not provide much warning before failure
D. Provides much greater time for remedial action before failure
What is the correct answer?
4
If T₁ and T₂ are the tensions on the tight and slack sides of the belt respectively, and Tc is the centrifugal tension, then initial tension in the belt is equal to
What is the correct answer?
4
Which of the following statement is wrong?
A. The pitch of rivets is obtained by equating the tearing resistance of the plate to the shearing resistance of the rivets
B. The pitch of rivets should not be less than 2d, where d is the diameter of rivet hole
C. The maximum value of the pitch of rivets for a longitudinal joint of a boiler, as per I.B.R., is given by Pmax = C.t + 41.28 mm
D. According to I.B.R., the thickness of butt strap shall not be less than 5 mm
What is the correct answer?
4
Which of the following is a permanent fastening?
What is the correct answer?
4
The initial tension (in newtons) in a bolt used for making a fluid tight joint like steam engine cover joints, is calculated by the relation (where d = Nominal diameter of bolt in mm)
What is the correct answer?
4
The building up of worn and undersized parts, subjected to repeated loads by electroplating is
C. Has no effect as regards fatigue strength
What is the correct answer?
4
Resistance to fatigue of a material is measured by
B. Coefficient of elasticity
What is the correct answer?
4
A metal pipe of 1 m diameter contains a fluid having a pressure of 1 N/mm². If the permissible tensile stress in the metal is 20 N/mm², then the thickness of the metal required for making the pipe will be
What is the correct answer?
4
The included angle for the V-belt is usually
What is the correct answer?
4
In Vickers hardness testing, the pyramid indentor apex is
What is the correct answer?
4
The ratio of circumferential stress to longitudinal stress in a thin cylinder subjected to an internal pressure is
What is the correct answer?
4
The allowable static stress for steel gears is approximately __________ of the ultimate tensile stress.
What is the correct answer?
4
When a material is subjected to fatigue loading, the ratio of the endurance limit to the ultimate tensile strength is
What is the correct answer?
4
The creep in the belt is due to
A. Effect of temperature on belt
C. Unequal extensions in the belt due to tight and slack side tensions
D. Stresses beyond elastic limit of belt material
What is the correct answer?
4
In an oil lubricated journal bearing, the coefficient of friction between the journal and the bearing
A. Remains constant at all speeds
B. Is minimum at zero speed and increases monotonically with increase in speed
C. Is maximum at zero speed and decreases monotonically with increase in speed
D. Becomes minimum at an optimum speed and then increases with further increase in speed