Related Questions
What is the correct answer?
4
The distribution of the forces along the length of key fitted in a shaft
C. Varies exponentially, being more near the torque-input end
D. Varies exponentially, being less near the torque-input end
What is the correct answer?
4
A shaft is subjected to fluctuating loads for which the normal torque (T) and bending moment (M) are 1000 N-m and 500 N-m respectively. If the combined shock and fatigue factor for bending is 1.5 and combined shock and fatigue factor for torsion is 2, then the equivalent twisting moment for the shaft is
What is the correct answer?
4
The pitch diameter is the __________ diameter of an external or internal screw thread.
What is the correct answer?
4
When a circular beam of diameter d is subjected to a shear force F, the maximum shear stress induced will be
What is the correct answer?
4
The centre to centre distance between two consecutive rivets in a row, is called
What is the correct answer?
4
The wire ropes make contact at
A. Bottom of groove of the pulley
B. Sides and bottom of groove of the pulley
C. Anywhere in the groove of the pulley
D. Sides of groove of the pulley
What is the correct answer?
4
While designing a screw in a screw jack against buckling failure, the end conditions for the screw are taken as
C. One end fixed and the other end hinged
D. One end fixed and the other end free
What is the correct answer?
4
If the centre distance of the mating gears having involute teeth is increased, then the pressure angle
What is the correct answer?
4
Stress concentration is caused due to
A. Variations in load acting on a member
B. Variations in properties of materials in a member
C. Abrupt change of cross-section
What is the correct answer?
4
The circumferential and longitudinal strains in a cylindrical boiler under internal steam pressure are εc and εl respectively. The change in volume of the boiler cylinder per unit volume will be
What is the correct answer?
4
Which of the following material has the maximum ductility?
What is the correct answer?
4
The allowable static stress for steel gears is approximately __________ of the ultimate tensile stress.
What is the correct answer?
4
A special case of ductility which permits materials to be rolled or hammered into thin sheets, is called
What is the correct answer?
4
The included angle for the British Association thread is
What is the correct answer?
4
The shear plane in case of bolts should
A. Be across threaded portion of shank
B. Be parallel to axis of bolt
C. Be normal to threaded portion of shank
D. Never be across the threaded portion
What is the correct answer?
4
I.S. specifies following total number of grades of tolerances
What is the correct answer?
4
In a multiple V-belt drive, when a single belt is damaged, it is preferable to change the complete set in order to
C. Ensure uniform loading
D. Ensure proper alignment
What is the correct answer?
4
A leaf spring in automobiles is used
D. To store strain energy
What is the correct answer?
4
Antifriction bearings are
C. Thin lubricated bearings
What is the correct answer?
4
If shearing stress in nut is half the tensile stress in a bolt, then nut length should be equal to
B. 0.75 × diameter of bolt
C. 1.25 × diameter of bolt
D. 1.5 × diameter of bolt
What is the correct answer?
4
The resilience of a bolt may be increased by
A. Increasing its shank diameter
C. Decreasing its shank diameter
What is the correct answer?
4
If a shaft made from ductile material is subjected to combined bending and twisting moment, calculations based on which one of the following failure theories will give the most conservative value?
A. Maximum principal stress theory
B. Maximum shear stress theory
C. Maximum strain energy theory
D. Maximum distortion energy theory
What is the correct answer?
4
The form factor of a helical gear __________ with the increase in the helix angle.
What is the correct answer?
4
Which of the following pipe joints would be suitable for pipes carrying steam?
What is the correct answer?
4
In order to avoid tearing of the plate at an edge, the distance from the centre line of the rivet hole to the nearest edge of the plate should be equal to (where d = Diameter of rivet hole)
What is the correct answer?
4
The rivet head used for boiler plate riveting is usually
What is the correct answer?
4
When the connected members are very yielding (soft gasket) as compared to the bolt, then the resultant load on the bolt will be equal to the
C. Sum of the initial tension and external load applied
D. Initial tension or external load, whichever is greater
What is the correct answer?
4
In order to determine the stresses in a thin cylinder due to an internal pressure, it is assumed that
A. The effect of curvature of the cylinder wall is neglected
B. The tensile stresses are uniformly distributed over the section of the walls
C. The effect of the restraining action of the heads at the end of the pressure vessel is neglected
What is the correct answer?
4
A crankshaft is a __________ shaft.
What is the correct answer?
4
When bevel gears connect two shafts whose axes intersect at an angle greater than a right angle and one of the bevel gears has a pitch angle of 90°, then they are known as