Home
Current Affairs January 2024

What is the correct answer?

4

The static tooth load should be __________ the dynamic load.

A. Equal to

B. Less than

C. Greater than

D. None of these

Correct Answer :

C. Greater than


Related Questions

What is the correct answer?

4

A sliding bearing which operates without any lubricant present, is called

A. Zero film bearing

B. Boundary lubricated bearing

C. Hydrodynamic lubricated bearing

D. Hydrostatic lubricated bearing

What is the correct answer?

4

Turn buckle has

A. Right hand threads on bout ends

B. Left hand threads on both ends

C. Left hand threads on one end and right hand threads on other end

D. No threads

What is the correct answer?

4

Fabric belts are used in industrial applications because

A. They are cheap

B. They can work at high temperature

C. They are unaffected by moisture and humidity

D. None of the above

What is the correct answer?

4

The contact ratio for gears is

A. Zero

B. Less than one

C. Greater than one

D. None of these

What is the correct answer?

4

The shear stress in a beam varies from zero at the outer fibres to a maximum at the________.

A. Neutral surface

B. Upper surface

C. Lower surface

D. None of these

What is the correct answer?

4

While designing a screw in a screw jack against buckling failure, the end conditions for the screw are taken as

A. Both the ends fixed

B. Both the ends hinged

C. One end fixed and the other end hinged

D. One end fixed and the other end free

What is the correct answer?

4

The application of third type levers is found in

A. Handle of a hand pump

B. Hand wheel of a punching press

C. Lever of a loaded safety valve

D. A pair of tongs

What is the correct answer?

4

Which of the following has threads at both ends?

A. Bolt

B. Tap bolt

C. Stud

D. None of these

What is the correct answer?

4

The rolling contact bearings as compared to sliding contact bearings have

A. Low starting and low running friction except at very high speeds

B. Accuracy of shaft alignment

C. Small overall dimensions

D. All of the above

What is the correct answer?

4

When a bolt is subjected to shock loading, the resilience of the bolt should be considered in order to prevent breakage at the

A. Thread

B. Middle

C. Shank

D. Head

What is the correct answer?

4

A chain drive transmits __________ power as compared to belt drive.

A. More

B. Less

C. Same

D. None of these

What is the correct answer?

4

In worm gears, the angle between the tangent to the pitch helix and an element of the cylinder, is known as

A. Helix angle

B. Pressure angle

C. Pitch lead angle

D. None of these

What is the correct answer?

4

The bearings of medium series have capacity __________ over the light series.

A. 10 to 20 %

B. 20 to 30 %

C. 30 to 40 %

D. 40 to 50 %

What is the correct answer?

4

The notch sensitivity q is expressed in terms of fatigue stress concentration factor Kf and theoretical stress concentration factor Kt as

A. (Kf + 1)/ (Kt + 1)

B. (Kf - 1)/ (Kt - 1)

C. (Kt + 1)/ (Kf + 1)

D. (Kt - 1)/ (Kf - 1)

What is the correct answer?

4

The maximum efficiency of a square threaded screw is

A. (1 - sinφ)/ (1 + sinφ)

B. (1 + sinφ)/ (1 - sinφ)

C. (1 - sinφ)/ (1 + cosφ)

D. (1 + cosφ)/ (1 - sinφ)

What is the correct answer?

4

In a full journal bearing, the angle of contact of the bearing with the journal is

A. 120°

B. 180°

C. 270°

D. 360°

What is the correct answer?

4

According to I.B.R., the efficiency of a triple riveted butt joint with double straps of unequal width (5 rivets per pitch length) should be

A. 45 to 60 %

B. 63 to 70 %

C. 70 to 83 %

D. 80 to 90 %

What is the correct answer?

4

Taper usually provided on cotter is

A. 1 in 5

B. 1 in 10

C. 1 in 24

D. 1 in 40

What is the correct answer?

4

Tapered roller bearings can take

A. Axial load only

B. Both radial and axial loads and the ratio of these being greater than unity

C. Radial load only

D. Both radial and axial loads and the ratio of these being less than unity

What is the correct answer?

4

Two helical springs of the same material and of equal circular crosssection, length and number of turns, but having radii 80 mm and 40 mm, kept concentrically (smaller radius spring within the larger radius spring), are compressed between two parallel planes with a load W. The inner spring will carry a load equal to

A. W/2

B. 2W/3

C. W/9

D. 8W/9

What is the correct answer?

4

When bevel gears connect two shafts whose axes intersect at an angle greater than a right angle and one of the bevel gears has a pitch angle of 90°, then they are known as

A. Crown bevel gears

B. Angular bevel gears

C. Mitre gears

D. Internal bevel gears

What is the correct answer?

4

Form coefficient of spring is

A. Ratio of coil diameter to wire diameter

B. Load required to produce unit deflection

C. Its capability of storing energy

D. Concerned with strength of wire of spring

What is the correct answer?

4

When the shaft rotates in anticlockwise direction at slow speed in a bearing, it will

A. Have contact at the bottom most of the bearing

B. Move towards right of the bearing making no metal to metal contact

C. Move towards right of the bearing making the metal to metal contact

D. Move towards left of the bearing making metal to metal contact

What is the correct answer?

4

In case of pressure vessels having closed ends, the fluid pressure induces

A. Longitudinal stress

B. Shear stress

C. Circumferential stress

D. None of these

What is the correct answer?

4

The pitch of threads on a Jock nut in comparison to pitch of nut is

A. Same

B. Coarser

C. Finer

D. Very fine

What is the correct answer?

4

The property of a material which enables it to resist fracture due to high impact loads is known as

A. Elasticity

B. Endurance

C. Strength

D. Toughness

What is the correct answer?

4

When an open coiled helical compression spring is subjected to an axial compressive load, the maximum shear stress induced in the wire is (where D = Mean diameter of the spring coil, d = Diameter of the spring wire, K = Wahl's stress factor, and W = Axial compressive load on the spring)

A. (WD/ πd3) × K

B. (2WD/ πd3) × K

C. (4WD/ πd3) × K

D. (8WD/ πd3) × K

What is the correct answer?

4

The radial distance of a tooth from the pitch circle to the top of the tooth is called

A. Addendum

B. Dedendum

C. Clearance

D. Working depth

What is the correct answer?

4

Belt slip may occur due to

A. Heavy load

B. Loose belt

C. Driving pulley too small

D. All of the above

What is the correct answer?

4

Factor of safety for fatigue loading is the ratio of

A. Elastic limit to the working stress

B. Elastic limit to the yield point

C. Endurance limit to the working stress

D. Young's modulus to the ultimate tensile strength