Home
Current Affairs January 2024

What is the correct answer?

4

The tailstock set over required to turn a taper on the entire length of a workpiece having diameters D and d is

A. (D - d)/2L

B. (D - d)/L

C. (D - d)/2

D. D - d

Correct Answer :

C. (D - d)/2


Related Questions

What is the correct answer?

4

In up-cut milling the work piece is fed

A. Against the rotating cutter

B. At angle of 60° to the cutter

C. In the direction of the cutter

D. At the right angle to the cutter

What is the correct answer?

4

Two 1 mm thick steel sheets are to be spot welded at a current of 5000 A. Assuming effective resistance to be 200 μm and current flow time of 0.2 second, heat generated during the process will be

A. 0.2 Joule

B. 1 Joule

C. 5 Joule

D. 1000 Joule

What is the correct answer?

4

In a single point turning operation with a cemented carbide and steel combination having a Taylor exponent of 0.25, if the cutting speed is halved, then tool life will become

A. Half

B. Two times

C. Eight times

D. Sixteen times

What is the correct answer?

4

The width of cutting edge of a parting off tool varies from

A. 3 to 12 mm

B. 5 to 20 mm

C. 8 to 30 mm

D. 15 to 40 mm

What is the correct answer?

4

For turning internal tapers, the suitable method is

A. By a form tool

B. By setting over the tail stock

C. By a taper turning attachment

D. By swivelling the compound rest

What is the correct answer?

4

For generating a Coons surface we require

A. A set of grid points on the surface

B. A set of grid control points

C. Four bounding curves defining the surface

D. Two bounding curves and a set of grid control points

What is the correct answer?

4

Soft materials can not be economically ground due to

A. High temperature involved

B. Frequent wheel clogging

C. Rapid wheel wear

D. Low work piece stiffness

What is the correct answer?

4

The purpose of jigs and fixtures is to

A. Increase machining accuracy

B. Facilitate interchangeability

C. Decrease expenditure on quality control

D. All of these

What is the correct answer?

4

In centreless grinders, the regulating wheel is inclined at

A. 0° to 8°

B. 9° to 15°

C. 16° to 20°

D. 21° to 25°

What is the correct answer?

4

A right hand tool on a lathe cuts most efficiently when it travels

A. From left to right end of the lathe bed

B. From right to left end of the lathe bed

C. With the help of a compound slide

D. Across the bed

What is the correct answer?

4

Lathe bed is made of

A. Mild steel

B. Alloy steel

C. Pig iron

D. Chilled cast iron

What is the correct answer?

4

In a single point tool, the angle between the surface of the flank immediately below the point and a line drawn from the point perpendicular to the base, is known as

A. Side relief angle

B. End relief angle

C. Back rake angle

D. Side rake angle

What is the correct answer?

4

The advantage of a broaching operation is that

A. Rate of production is very high

B. High accuracy and high class of surface finish is possible

C. Roughing and finishing cuts are completed in one pass of the tool

D. All of the above

What is the correct answer?

4

In a CNC program block, N002 GO2 G91 X40 Z40......, GO2 and G91 refer to

A. Circular interpolation in counter clockwise direction and incremental dimension

B. Circular interpolation in counter clockwise direction and absolute dimension

C. Circular interpolation in clockwise direction and incremental dimension

D. Circular interpolation in clockwise direction and absolute dimension

What is the correct answer?

4

The common welding error that occurs due to wrong speed, faulty preparation, and high / low current, improper electrode size is called?

A. Distortion

B. Warping

C. Porous weld

D. Poor fusion

What is the correct answer?

4

The surface finish is improved by the increase in

A. Cutting speed

B. Nose radius

C. True rake angle

D. All of these

What is the correct answer?

4

When the tool moves parallel to the lathe axis, the movement is termed as

A. Cross feed

B. Angular feed

C. Longitudinal feed

D. Any one of these

What is the correct answer?

4

What is the type of shielding gas for GTAW (Gas Tungsten Arc Welding) used for carbon steels only called?

A. Argon H₂

B. Argon CO₂

C. Argon Helium

D. Helium

What is the correct answer?

4

Internal gear cutting operation can be performed by

A. Milling

B. Shaping with rack cutter

C. Shaping with pinion cutter

D. Hobbing

What is the correct answer?

4

The maximum possible draft in cold rolling of sheet increases with the

A. Increase in coefficient of friction

B. Decrease in coefficient of friction

C. Decrease in roll radius

D. Decrease in roll velocity

What is the correct answer?

4

Tumbler gears in lathe are used to

A. Reduce the spindle speed

B. Cut gears

C. Give desired direction of movement to the lathe carriage

D. Drill a workpiece

What is the correct answer?

4

The cutting angle of a flat drill varies from

A. 3° to 8°

B. 20° to 30°

C. 60° to 90°

D. 90° to 120°

What is the correct answer?

4

Which type of motor is not used in axis or spindle drives of CNC machine tools?

A. Induction motor

B. DC servo motor

C. Stepper motor

D. Linear servo motor

What is the correct answer?

4

The silicon carbide abrasive is chiefly used for grinding

A. Cemented carbide

B. Ceramic

C. Cast iron

D. All of these

What is the correct answer?

4

Work speed of circular electrode of 220 mm diameter for carrying out seam welding at 4 welds per cm on 1.6 mm thick mild steel tube. Welding cycle consists of 3 cycles on and 2 cycles off Power supply is at 50 Hz. Calculate R.P.M. and energy requirement of the above circular electrodes assuming effective resistance between electrodes as 100 ohm.

A. 2.17 rpm, 600 joules

B. 6.8 rpm, 6 joules

C. 5.03 rpm, 600 joules

D. 22 rpm, 600 joules

What is the correct answer?

4

Glazing in grinding wheels can be decreased by

A. Using a harder wheel or by increasing the wheel speed

B. Using a softer wheel or by decreasing the wheel speed

C. Using a harder wheel or by decreasing the wheel speed

D. Using a softer wheel or by increasing the wheel speed

What is the correct answer?

4

The tail stock set over method of taper turning is preferred for

A. Internal tapers

B. Small tapers

C. Long slender tapers

D. Steep tapers

What is the correct answer?

4

The main purpose of spheroidising treatment is to improve

A. Hardenability of low carbon steels

B. Machinability of low carbon steels

C. Hardenability of high carbon steels

D. Machinability of high carbon steels

What is the correct answer?

4

Which one of the following is a solid state joining process?

A. Gas tungsten arc welding

B. Resistance spot welding

C. Friction welding

D. Submerged arc welding

What is the correct answer?

4

Side relief angle of a single point tool is the angle

A. By which the face of the tool is inclined towards back

B. By which the face of the tool is inclined sideways

C. Between the surface of the flank immediately below the point and a plane at right angles to the centre line of the point of tool

D. Between the surface of the flank immediately below the point and a line drawn from the point perpendicular to the base