Related Questions
What is the correct answer?
4
This is the intersection of the ground plane with the picture plane:
What is the correct answer?
4
This type of drawing is created to calculate areas, locate property lines, and locate building projects and facilities:
What is the correct answer?
4
A partial auxiliary view usually shows only features on the ________ of the inclined line and not any projection of other planes.
What is the correct answer?
4
When filling an area with a hatch pattern in Auto-CAD the drafter needs to be able to ________.
A. See the entire bounding area to hatch
D. Set the layer to Defpoints
What is the correct answer?
4
This is a line terminated by arrowheads, indicating the direction and extent of a dimension:
What is the correct answer?
4
The title block used on working drawings should include the __________.
What is the correct answer?
4
An engineer's scale would be used to measure lines on a drawing where the scale factor reads ________.
What is the correct answer?
4
Drawings created with commercial software are typically saved as:
What is the correct answer?
4
It is customary for the first sheet of a working drawing set to include ________.
What is the correct answer?
4
The second line of dimensions out from the plan generally includes ________.
A. Centers of doors and windows
B. The distances between outside walls and interior walls
C. The measurement from the outside of the brick to the inside of the exterior wall
D. The measurement from one outside corner to the opposite outside corner
What is the correct answer?
4
These types of projectors converge at a vanishing point:
What is the correct answer?
4
A projection weld is a type of:
What is the correct answer?
4
The first step in creating a traditional technical drawing is to ________.
A. Draw a series of guide lines
C. Align the paper so that it will be positioned square to the parallel bar
D. Sharpen the leads in the technical pens
What is the correct answer?
4
A secondary auxiliary view is a projection off of the ________.
C. Primary auxiliary view
What is the correct answer?
4
Oblique drawings are dimensioned in a similar fashion as these types of drawings:
What is the correct answer?
4
The most common geometric form used in gears today is this:
What is the correct answer?
4
Schematic and single-line diagrams should be arranged so that signal or transmission path from input to output proceeds in this fashion:
A. Right to left and top to bottom
B. Right to left and bottom to top
C. Left to right and top to bottom
D. Left to right and bottom to top
What is the correct answer?
4
In order to create an isometric circle to represent a hole through the top surface of a box, the drafter must insure that the correct iso-plane has been selected by scrolling through the iso-planes using the ________ key.
What is the correct answer?
4
In oblique projection, important shapes should be in this position relative to the viewing plane:
What is the correct answer?
4
This is a systematic approach that integrates the design and manufacture of products with the goal of optimizing the process:
A. Traditional engineering design
B. The manufacturing process
What is the correct answer?
4
This type of auxiliary view is projected onto a plane that is perpendicular to one of the principal planes of projection:
What is the correct answer?
4
These weld symbols have no arrow-side or other-side significance:
A. Projection or seam weld
C. Surface or groove weld
What is the correct answer?
4
How can the drafter prevent Auto-CAD from placing or stacking another center mark on a circle when adding a diameter dimension to it?
A. Explode the dimension and then erase the center mark
B. Use the Properties dialog box to turn off the center mark of the dimension
D. Use the trim tool to take away the stacked center mark
What is the correct answer?
4
If a plane is parallel to the plane of projection, it appears:
What is the correct answer?
4
In this type of section, one quarter of the object is removed:
What is the correct answer?
4
A ________ section allows the drafter to create a Cutting Plane line which is not in a straight line across the part.
What is the correct answer?
4
These are accurately drawn maps of cities and towns showing property lines and other features that control property ownership:
What is the correct answer?
4
The MASSPROP shortcut will provide the following information.
What is the correct answer?
4
This is how axonometric, oblique, and perspective sketches show objects:
What is the correct answer?
4
This allows the designer to conceptualize objects more easily without having to make costly illustrations, models, or prototypes:
A. Computer-aided manufacturing
C. Computer-aided engineering
D. Computer-aided prototyping