Home
Current Affairs January 2024

What is the correct answer?

4

The top and sides of the table of a shaper usually have

A. L-type slots

B. T-type slots

C. I-type slots

D. Any one of these

Correct Answer :

B. T-type slots


Related Questions

What is the correct answer?

4

As the cutting speed increases, the tool cutting forces

A. Remain constant

B. Increases

C. Decreases

D. First increases and then decreases

What is the correct answer?

4

For softer materials, the point angle of the drill is kept

A. Equal to 118°

B. Less than 118°

C. More than 118°

D. Any one of these

What is the correct answer?

4

The cutting speed for drilling aluminium, brass and bronze with carbon steel drills is _________ cutting speed for drilling mild steel with high speed steel drills.

A. Equal to

B. Less than

C. More than

D. None of these

What is the correct answer?

4

Which of the following parameters influence the axial feed rate in centerless grinding?

A. Regulating wheel diameter

B. Speed of the regulating wheel

C. Angle between the axes of grinding and regulating wheels

D. All of the above

What is the correct answer?

4

Drilling is an example of

A. Orthogonal cutting

B. Oblique cutting

C. Simple cutting

D. Uniform cutting

What is the correct answer?

4

When the shear angle is small

A. Path of shear is short and chip is thin

B. Path of shear is large and chip is thick

C. Path of shear is short and chip is thick

D. Path of shear is large and chip is thin

What is the correct answer?

4

Down milling is also called

A. Conventional milling

B. Climb milling

C. End milling

D. Face milling

What is the correct answer?

4

The tool may fail due to

A. Cracking at the cutting edge due to thermal stresses

B. Chipping of the cutting edge

C. Plastic deformation of the cutting edge

D. All of these

What is the correct answer?

4

Twist drills are made of

A. High speed steel

B. Carbon steel

C. Stainless steel

D. Either (A) or (B)

What is the correct answer?

4

For machining a mild steel workpiece using carbide tool, the maximum material will be removed at a temperature of

A. 50°C

B. 100°C

C. 175°C

D. 275°C

What is the correct answer?

4

The swing diameter over the bed is ________ the height of the centre measured from the bed of the lathe.

A. Equal to

B. Twice

C. Thrice

D. One-half

What is the correct answer?

4

A jig is defined as a device which

A. Holds and locates a workpiece and guides and controls one or more cutting tools

B. Holds and locates a workpiece during an inspection or for a manufacturing operation

C. Is used to check the accuracy of workpiece

D. All of the above

What is the correct answer?

4

In up milling, the thickness of chip is

A. Minimum at the beginning of the cut and maximum at the end of the cut

B. Maximum at the beginning of the cut and minimum at the end of the cut

C. Uniform throughout the cut

D. None of these

What is the correct answer?

4

Ceramic cutting tools are

A. Made by cold pressing of aluminium oxide powder

B. Available in the form of tips

C. Brittle and have low bending strength

D. All of these

What is the correct answer?

4

Tool life is measured by the

A. Number of pieces machined between tool sharpenings

B. Time the tool is in contact with the job

C. Volume of material removed between tool sharpenings

D. All of the above

What is the correct answer?

4

The tail stock set over method of taper turning is preferred for

A. Internal tapers

B. Small tapers

C. Long slender tapers

D. Steep tapers

What is the correct answer?

4

The main purpose of a boring operation, as compared to drilling, is to

A. Drill a hole

B. Finish the drilled hole

C. Correct the hole

D. Enlarge the existing hole

What is the correct answer?

4

When the metal is removed by erosion caused by rapidly recurring spark discharges between the tool and work, the process is known as

A. Electrochemical machining

B. Electro-discharge machining

C. Ultrasonic machining

D. None of these

What is the correct answer?

4

If the helix angle of the drill is made _________ 30°, then the torque required to drive the drill at a given feed will be more.

A. Equal to

B. Less than

C. More than

D. None of these

What is the correct answer?

4

Tool life is generally better when

A. Grain size of the metal is large

B. Grain size of the metal is small

C. Hard constituents are present in the microstructure of the tool material

D. None of the above

What is the correct answer?

4

The lead screw of a lathe has _________ threads.

A. Single start

B. Double start

C. Multi-start

D. Any one of these

What is the correct answer?

4

The object of caulking in a riveted joint is to make the joint

A. Free from corrosion

B. Stronger in tension

C. Free from stresses

D. Leak-proof

What is the correct answer?

4

The cutting force in punching and blanking operations mainly depends on

A. The modulus of elasticity of metal

B. The shear strength of metal

C. The bulk modulus of metal

D. The yield strength of metal

What is the correct answer?

4

Two plates of the same metal having equal thickness are to be butt welded with electric arc. When the plate thickness changes, welding is achieved by

A. Adjusting the current

B. Adjusting the duration of current

C. Changing the electrode size

D. Changing the electrode coating

What is the correct answer?

4

The advantage of a broaching operation is that

A. Rate of production is very high

B. High accuracy and high class of surface finish is possible

C. Roughing and finishing cuts are completed in one pass of the tool

D. All of the above

What is the correct answer?

4

The relief or clearance at the cutting edge of a flat drill varies from

A. 3° to 8°

B. 20° to 30°

C. 60° to 90°

D. 90° to 120°

What is the correct answer?

4

Allowance in limits and fits refers to

A. Maximum clearance between shaft and hole

B. Minimum clearance between shaft and hole

C. Difference between maximum and minimum sizes of hole

D. Difference between maximum and minimum sizes of shaft

What is the correct answer?

4

When 3-2-1 principle is used to support and locate a three dimensional work-piece during machining, the number of degrees of freedom that are restricted is

A. 7

B. 8

C. 9

D. 10

What is the correct answer?

4

The broaching operation in which the work moves past the stationary tool is called

A. Pull broaching

B. Push broaching

C. Surface broaching

D. Continuous broaching

What is the correct answer?

4

Lapping is an operation of

A. Making a cone-shaped enlargement of the end of a hole

B. Smoothing and squaring the surface around a hole

C. Sizing and finishing a small diameter hole

D. Producing a hole by removing metal along the circumference of a hollow cutting tool