Related Questions
What is the correct answer?
4
A differential pulley block has larger and smaller diameters of 100 mm and 80 mm respectively. Its velocity ratio is
What is the correct answer?
4
The linear acceleration (a) of a body rotating along a circular path of radius (r) with an angular acceleration of α rad/s2, is
What is the correct answer?
4
Moment of inertia of a hollow circular section, as shown in the below figure about X-axis, is
What is the correct answer?
4
The necessary condition for forces to be in equilibrium is that these should be
C. Both (A) and (B) above
What is the correct answer?
4
The skidding away of the vehicle on a level circular path can be avoided if the force of friction between the wheels and the ground is __________ the centrifugal force.
What is the correct answer?
4
The acceleration of a particle moving with simple harmonic motion is __________ at the mean position.
What is the correct answer?
4
The friction experienced by a body, when in motion, is known as
What is the correct answer?
4
The forces, which meet at one point, but their lines of action do not lie in a plane, are called
A. Coplanar non-concurrent forces
B. Non-coplanar concurrent forces
C. Non-coplanar non-concurrent forces
What is the correct answer?
4
The centre of percussion of a solid cylinder of radius r resting on a horizontal plane will be
What is the correct answer?
4
Pick up wrong statement about friction force for dry surfaces. Friction force is
A. Proportional to normal load between the surfaces
B. Dependent on the materials of contact surface
C. Proportional to velocity of sliding
D. Independent of the area of contact surfaces
What is the correct answer?
4
According to Lamis theorem
A. The three forces must be equal
B. The three forces must be at 120° to each other
C. The three forces must be in equilibrium
D. If the three forces acting at a point are in equilibrium, then each force is proportional to the sine of the angle between the other two
What is the correct answer?
4
The units of moment of inertia of mass are
What is the correct answer?
4
The velocity ratio of a single purchase crab winch can be increased by
A. Increasing the length of the handle
B. Increasing the radius of the load drum
C. Increasing the number of teeth of the pinion
What is the correct answer?
4
Two balls of equal mass and of perfectly elastic material are lying on the floor. One of the balls with velocity v is made to strike the second ball. Both the balls after impact will move with a velocity
What is the correct answer?
4
A circular hole of 50 mm diameter is cut out from a circular disc of 100 mm diameter as shown in the below figure. The centre of gravity of the section will lie
What is the correct answer?
4
If the resultant of two equal forces has the same magnitude as either of the forces, then the angle between the two forces is
What is the correct answer?
4
On the ladder resting on the ground and leaning against a smooth vertical wall, the force of friction will be
A. Downwards at its upper end
B. Upwards at its upper end
C. Perpendicular to the wall at its upper end
What is the correct answer?
4
The product of either force of couple with the arm of the couple is called
What is the correct answer?
4
Forces are called coplanar when all of them acting on body lie in
What is the correct answer?
4
The rate of change of displacement of a body is called
What is the correct answer?
4
In the shown figure, if the angle of inclination of the plane is increased, then acceleration of the system will
What is the correct answer?
4
The motion of a particle round a fixed axis is
D. Translatory as well as rotary
What is the correct answer?
4
Limiting force of friction is the
A. Tangent of angle between normal reaction and the resultant of normal reaction and limiting friction
B. Ratio of limiting friction and normal reaction
C. The friction force acting when the body is just about to move
D. The friction force acting when the body is in motion
What is the correct answer?
4
Two coplanar couples having equal and opposite moments
B. Produce a couple and an unbalanced force
D. Cannot balance each other
What is the correct answer?
4
Dynamic friction as compared to static friction is
D. May be less of more depending on nature of surfaces and velocity
What is the correct answer?
4
The energy possessed by a body, for doing work by virtue of its position, is called
What is the correct answer?
4
Non-coplanar concurrent forces are those forces which
A. Meet at one point, but their lines of action do not lie on the same plane
B. Do not meet at one point and their lines of action do not lie on the same plane
C. Meet at one point and their lines of action also lie on the same plane
D. Do not meet at one point, but their lines of action lie on the same plane
What is the correct answer?
4
Moment of inertia of a triangular section of base (b) and height (h) about an axis passing through its vertex and parallel to the base, is __________ than that passing through its C.G. and parallel to the base.
What is the correct answer?
4
If a number of forces are acting at a point, their resultant will be inclined at an angle θ with the horizontal, such that
What is the correct answer?
4
Which of the following is not the unit of work, energy and heat?