Related Questions
What is the correct answer?
4
The minimum temperature to which the water can be cooled in a cooling tower is the __________ temperature of air.
What is the correct answer?
4
Spherical shape of mercury droplets is due to its
What is the correct answer?
4
Which of the following emissions in the exhaust gas of an I.C. engine causes the formation of photochemical smog?
What is the correct answer?
4
Unit of surface tension in S.I. unit is
B. Joule/
C. Newton/
What is the correct answer?
4
Main constituent of bone ash is
What is the correct answer?
4
Which of the following is normally not found in both the S.I. (petrol) & C.I. (diesel) engines?
What is the correct answer?
4
Addition of small amount of __________ to grey cast iron is done to produce nodular grey cast iron.
What is the correct answer?
4
Large diameter reinforced cement concrete (RCC) pipes are generally joined by __________ joint.
What is the correct answer?
4
Super conduction in metals is observed at a temperature of __________ °K.
What is the correct answer?
4
Transition from laminar flow to turbulent flow in fluid flow through a pipe does not depend upon the
What is the correct answer?
4
Working of linear variable differential transducer (LVDT) is based on the principle of variable
What is the correct answer?
4
What happens, when SO2 is passed through a solution of H2S in water?
A. Precipitation of sulphur takes place
What is the correct answer?
4
According to maximum shear stress failure criterion, yielding in material occurs, when the maximum shear stress is equal to __________ times the yield stress.
What is the correct answer?
4
Internal energy of a gas obeying Van-Der- Waals equation of state, [p + (a/v2)] (V - b) = RT, depends upon its
A. Pressure & temperature
B. Pressure & specific volume
C. Temperature & specific volume
What is the correct answer?
4
Diameter of the rivet to be provided on a 20 mm. thick boiler plate will be __________ mm.
What is the correct answer?
4
Use of economiser in a boiler plant reduces the fuel consumption for steam generation by about __________ percent.
What is the correct answer?
4
In case of compression of one kg of air, the work done will be the least, when the value of polytropic index 'n' is
What is the correct answer?
4
The most important requirement for aluminium industry is the availability of cheap
What is the correct answer?
4
L.D. (Linz-Donawitz) converter is used in the production of
What is the correct answer?
4
Alloys having more than 80% copper are generally more
C. Prone to season cracking
What is the correct answer?
4
Which of the following has the highest modulus of elasticity (about 7 × 106 kg/cm2)?
What is the correct answer?
4
Coating thickness in case of galvanising of steel sheet generally corresponds to the deposition of __________ gms of zinc per of steel strip.
What is the correct answer?
4
Which of the following is not a ferromagnetic material?
What is the correct answer?
4
Corrosion rate cannot be lowered by reducing the __________ of the corroding medium.
What is the correct answer?
4
A dummy activity is used in PERT network to describe the
A. Precedence relationship
What is the correct answer?
4
Direct conversion of thermal energy to electrical energy is facilitated by the
C. Magneto hydrodynamic generator
What is the correct answer?
4
Powder metallurgy technique is used in the production of __________ tools.
What is the correct answer?
4
A spring material should have low
What is the correct answer?
4
Work required for compression of a gas contained in a cylinder is 7000 kJ. During compression, heat interaction of 3000 kJ causes the surroundings to be heated. Internal energy change of the gas during the compression is __________ kJ.
What is the correct answer?
4
__________ stress cannot be sustained by a fluid in equilibrium.