Related Questions
What is the correct answer?
4
The piece of a brick cut with its one corner equivalent to half the length and half the width of a full brick, is known as
What is the correct answer?
4
In case of Raymond pile
A. Lengths vary from 6 m to 12 m
B. Diameter of top of piles varies from 40 cm to 60 cm
C. Diameter of pile at bottom varies from 20 cm to 28 cm
What is the correct answer?
4
The pile which supports the load partly by friction and partly by resting on hard stratum, is called
What is the correct answer?
4
The vertical faces of a door opening which support frame of the door, are
What is the correct answer?
4
Rotary drilling is the fastest method in case of
What is the correct answer?
4
Cast iron piles
A. Are suitable for works under sea water
B. Resist shocks or vibrations
C. Are suitable for use as batter piles
D. Are useful for heavy vertical loads
What is the correct answer?
4
A temporary rigid structure having platforms to enable masons to work at different stages of a building, is known as
What is the correct answer?
4
The maximum permissible differential settlement, in case of foundations in clayey soil, is usually limited to
What is the correct answer?
4
The Auger borings are not common
A. In soils that require lateral support
What is the correct answer?
4
The 9 cm × 9 cm side of a brick as seen in the wall face, is generally known as
What is the correct answer?
4
The local swelling of a finished plaster, is termed
What is the correct answer?
4
Pick up the correct statement from the following:
A. A mortar joint having a concave finishing in brick masonry, is called keyed joint
B. A mortar joint projecting beyond the face of a masonry wall, is called tucked joint
C. A mortar joint having a recess in it, is called ruled joint
What is the correct answer?
4
The important test to be conducted on a stone used in docks and harbours is
What is the correct answer?
4
Ornamental moulded course placed on the top of a wall, is
What is the correct answer?
4
Pick up the correct statement from the following:
A. The pile driven in sand is called sand pile
B. The drilled hole filled with sand is called sand pile
C. The sand piles are used for bearing purposes
What is the correct answer?
4
Which one of the following piles has a cast iron shoe even after removal of the hollow cylindrical steel casing?
D. Both (a) and (c) of the above
What is the correct answer?
4
The type of roof suitable in plains where rainfall is meagre and temperature is high is
A. Pitched and sloping roof
What is the correct answer?
4
The size of a floor tile commonly used, is
A. 15 cm × 15 cm × 1.8 cm
C. 22.5 × 22.5 cm × 2.2 cm
What is the correct answer?
4
The art of bringing the floor to a true level surface by means of screeds, is called
What is the correct answer?
4
The Auger boring method is not suitable for
What is the correct answer?
4
In any good staircase, the maximum and minimum pitch respectively should be
What is the correct answer?
4
The type of roof which slopes in two directions with a break in the slope on each side is known as
What is the correct answer?
4
Number of vertical joints in a stretcher course is x times the number of joints in the header course, where x is equal to
What is the correct answer?
4
The projections of head or sill of a door or window frame are
What is the correct answer?
4
Which of the following metal sheets is most effective in preventing dampness?
What is the correct answer?
4
The maximum number of steps in a flight should generally be restricted to
What is the correct answer?
4
Exposed portions of vertical surface at right angles to the door or window frame, are known as
What is the correct answer?
4
The brick laid with its breadth parallel to the face of a wall, is known as
What is the correct answer?
4
The concrete slump recommended for beams and slabs; is
What is the correct answer?
4
The arrangement of supporting an existing structure by providing supports underneath, is known as