Related Questions
What is the correct answer?
4
The building construction industry relies on sets of ________ drawings to construct homes and commercial buildings.
What is the correct answer?
4
This type of thread is a thread on the inside of a member:
What is the correct answer?
4
When designing a home for a client, one of the most important predesign considerations that an architect needs to address is ________.
A. How much money the client is willing to spend
B. The site on which the house is to sit
C. The nearest grocery store
D. Whether or not there is a curb and gutter system
What is the correct answer?
4
The distance a screw thread advances axially in one turn is the:
What is the correct answer?
4
Two-point perspective is also known as:
What is the correct answer?
4
This is the most common application for developments and intersections:
A. Sheet metal construction
D. Mechanical engineering
What is the correct answer?
4
This type of section is not in direct projection from the view containing the cutting plane:
What is the correct answer?
4
Spur gear design normally begins with selecting this:
What is the correct answer?
4
In isometric projection, all distances are approximately this percentage of their true size:
What is the correct answer?
4
This type of projection is when projectors are parallel to each other, but is at an angle other than 90 degrees to the plane of projection:
B. Perpendicular projection
What is the correct answer?
4
The most common geometric form used in gears today is this:
What is the correct answer?
4
These maps are used to plan construction projects that locate construction features so they fit the topography of the area:
C. Structural topography maps
D. Structure location plans
What is the correct answer?
4
Elevation drawings will include information about ________.
What is the correct answer?
4
These breaks are used to shorten the view of an object:
What is the correct answer?
4
This type of solid is egg-shaped and can be created by revolving an ellipse around one of its axes:
What is the correct answer?
4
In this type of concrete, the steel is pre-tensioned before the superimposed load is applied:
What is the correct answer?
4
Dimensions are used on the elevation plan to describe ________.
A. Finished floor elevations
What is the correct answer?
4
These weld symbols have no arrow-side or other-side significance:
A. Projection or seam weld
C. Surface or groove weld
What is the correct answer?
4
How can the drafter prevent Auto-CAD from placing or stacking another center mark on a circle when adding a diameter dimension to it?
A. Explode the dimension and then erase the center mark
B. Use the Properties dialog box to turn off the center mark of the dimension
D. Use the trim tool to take away the stacked center mark
What is the correct answer?
4
Using the Relative Polar Coordinate System to add a 3 inch line that is 45 degrees from the end point of the line created above the drafter would ________.
B. Type 3 back slash and enter
C. Type 3 forward slash and enter
D. Type 3 and try to use the Dynamic Input readout to find the end point
What is the correct answer?
4
The ________ tool on the Dimension tool bar places the length of an arch on a drawing.
What is the correct answer?
4
This type of axonometric drawing has equal foreshortening along two axis directions and a different amount on the third axis:
What is the correct answer?
4
The condition of a part when it contains the least amount of material is referred to as ________.
What is the correct answer?
4
The title block used on working drawings should include the __________.
What is the correct answer?
4
Several of the tools used in traditional drafting include the following:
A. Parallel straight edge
What is the correct answer?
4
If a plane is parallel to the plane of projection, it appears:
What is the correct answer?
4
Objects that are symmetric can be shown effectively using this type of section:
What is the correct answer?
4
This is a solid shape that fits inside the mold and forms a hole in a cooled cast metal or molten plastic object:
What is the correct answer?
4
9.The lines used to create the auxiliary view should appear as ________ in the finished view.
What is the correct answer?
4
One way to evenly space dimensions on a drawing is to use the ________.