Related Questions
What is the correct answer?
4
The unit of gc is
What is the correct answer?
4
To counteract the bad effects of strain hardening on a cold formed part, it must be
What is the correct answer?
4
Surface tension of a liquid
A. Is due to intermolecular forces of cohesion
B. Decreases with rise in temperature
C. Is responsible for the spherical shape of an isolated liquid drop
What is the correct answer?
4
In Newton's law of viscosity, which states that the shear stress is proportional to the __________ Co-efficient of viscosity is called dynamic or absolute viscosity(where, V = velocity, = velocity gradient).
What is the correct answer?
4
Unit of surface tension in S.I. unit is
B. Joule/
C. Newton/
What is the correct answer?
4
Maximum change in the hardness of martensite occurs in the carbon content range of __________ percent in steel.
What is the correct answer?
4
Factor of safety is the ratio of the __________ stress to the working stress.
What is the correct answer?
4
Temperature of hot gases flowing in a pipe is measured by a thermocouple inserted in the thermal well. The thermal well made of __________ will facilitate the most accurate measurement of the temperature.
What is the correct answer?
4
High speed steel tools retain their hardness upto a temperature of __________ °C.
What is the correct answer?
4
The order of a chemical reaction
A. Can be determined only experimentally
B. Can be determined from the stoichiometry of the reaction
What is the correct answer?
4
Hot extrusion of aluminium is done in the temperature range of __________ °C.
What is the correct answer?
4
__________ is the most important element, which controls the physical properties of steel.
What is the correct answer?
4
The softness or hardness of a grinding wheel depends upon the type & amount of bonding material used. For general purpose cutter grinding __________ grinding wheel is normally used.
What is the correct answer?
4
With increase in annealing temperature, the following defect density decreases.
What is the correct answer?
4
The dew point of moist air becomes __________ with decrease in its relative humidity.
A. Less than the wet bulb temperature
B. More than the wet bulb temperature
C. More than the dry bulb temperature
D. Equal to wet bulb temperature
What is the correct answer?
4
In a neutral solution
C. Both H+ and OH- ions are present in very small but equal concentration
What is the correct answer?
4
Shrinkage allowance on pattern is provided to compensate for shrinkage when the
A. Metal changes from liquid state to solid state at freezing temperature
B. Solid phase temperature drops from freezing temperature to the room temperature
C. Liquid metal temperature drops from pouring temperature to room temperature
D. Liquid metal temperature drops from pouring temperature to freezing temperature
What is the correct answer?
4
The property of material, by which a given amount of energy is absorbed by it without plastic deformation, is called the
What is the correct answer?
4
A material subjected __________ must have high resilience.
What is the correct answer?
4
Out of the following __________ iron has the best capability to bear sudden & excessive shocks.
What is the correct answer?
4
All of the following alloying elements of steel increases hardness but sacrifice ductility, except
What is the correct answer?
4
Which of the following metals reacts violently with water?
What is the correct answer?
4
Pick out the wrong statement.
A. Lead can creep under its own weight at room temperature
B. The electrical conductivity of gold is considerably reduced by alloying additions due to the decrease in electron movement
C. Recrystallisation temperature decreases with decrease in strain in a cold worked metal
D. With increase in temperature, the electrical conductivity of intrinsic semi-conductor will increase
What is the correct answer?
4
The following type of bonding is strongly directional in solids.
What is the correct answer?
4
The taper provided on pattern for its easy & clean withdrawal from the mould is termed as the __________ allowance.
What is the correct answer?
4
Hot extrusion process is not used for making
A. Cast iron pipe for domestic water supply
B. Aluminium curtain rods
C. Stainless steel tubes used in furnitures
What is the correct answer?
4
Alloy powder manufactured by the following process have spherical shapes.
A. Electrochemical deposition
What is the correct answer?
4
Limestone addition in the blast furnace is done to flux __________ present in the raw materials.
What is the correct answer?
4
In electrical resistance welding, distortion results from the use of improper
What is the correct answer?
4
The critical pressure at which the latent heat of vaporisation of steam becomes zero is __________ Kg/cm2.