Related Questions
What is the correct answer?
4
The wet bulb temperature is lower in dry air than in wet air at the same temperature. A dry bulb thermometer registers a higher temperature than a wet bulb thermometer except at __________ percent relative humidity.
What is the correct answer?
4
Steel is welded using the __________ flame.
What is the correct answer?
4
Which of the following has the least value of ultimate tensile strength (UTS)?
What is the correct answer?
4
Photographic plates are coated with
What is the correct answer?
4
Yield strength of a material is determined by the __________ test.
What is the correct answer?
4
Work hardenable alloy steel used to make the bucket wheel excavators, blades of bulldozers and other earth moving equipments contain iron, carbon and
What is the correct answer?
4
Dowtherm is a
A. High temperature heating medium (a petroleum product)
B. Product of coal tar distillation
C. Very heat sensitive material
What is the correct answer?
4
__________ has a negative co-efficient of linear expansion.
What is the correct answer?
4
Addition of small amount of __________ to grey cast iron is done to produce nodular grey cast iron.
What is the correct answer?
4
While the thermosetting polymers are amorphous in nature, the thermoplastic polymers are either amorphous or crystalline. The crystalline polymers are characterised by the
C. Better finish and surface appearance
D. High plastic deformation
What is the correct answer?
4
'Cryogenics' is concerned with the generation & use of low temperature in the range of
What is the correct answer?
4
A cylindrical rod subjected to a tensile strain within the elastic limit undergoes a volume change. If the volume strain is equal to half the tensile strain, then the Poisson's ratio of the rod is
What is the correct answer?
4
Thermodynamic cycle involved in the working of a thermal power plant is the __________ cycle.
What is the correct answer?
4
__________ joint is mostly used for joining pipes carrying water at low pressure.
What is the correct answer?
4
__________ is not used as a material of construction in thermocouples.
What is the correct answer?
4
For preparation of porous bearings by powder metallurgy, preferred particle shape is
What is the correct answer?
4
Powder metallurgy process does not make metal powder by
D. Electrolytic deposition
What is the correct answer?
4
Pick out the wrong statement.
A. Cold cracking of a weld is due to the presence of hydrogen gas in the weld
B. True stress is given by, σ = σE (1 + εE), where σE and εE are engineering stress and engineering strain respectively
C. Phosphorous can be easily recovered in the iron blast furnace
D. High residual stress at the surface is beneficial for fatigue properties of a material
What is the correct answer?
4
The most abundant metal present in the earth's crust is;
What is the correct answer?
4
Damage to metal surface by mechanical action is called
What is the correct answer?
4
The property of material, by which a given amount of energy is absorbed by it, without plastic deformation, is called
What is the correct answer?
4
Which of the following hardness tests does not measure the indentation hardness of metals and alloys?
B. Shore scleroscope test
D. Rockwell hardness test
What is the correct answer?
4
When the wavelength of incident X-rays increases, the angle of diffraction
D. Shows no systematic variation
What is the correct answer?
4
Secondary hardening in steels arises out of the
A. Precipitation of fine alloy carbides at high temperatures
B. Refinement of ferrite grain size by working
C. Decomposition of retained austenite upon heat treatment
D. Precipitation of complex inter-metallic upon heat treatment
What is the correct answer?
4
Which of the following test is used for distinguishing among dry oils, semi-drying oils and non drying oils?
B. Reichert-Meissl value test
What is the correct answer?
4
Out of the following, maximum temperature drop for a given heat flow & for the same thickness will be in the case of
What is the correct answer?
4
At absolute zero temperature, for any reaction involving condensed phases
What is the correct answer?
4
Electrochemical corrosion can occur, only if __________ is present in contact with metal.
What is the correct answer?
4
What is the critical radius of insulation (cms) for a metallic cylinder, if the convective heat transfer co-efficient with the ambient atmosphere is 5 W/m2. °K? Thermal conductivity of metal and insulation material are 40 and 0.1 W/m.°K respectively.
What is the correct answer?
4
Materials having __________ lattice structure are usually the most ductile.
A. Body centred cubic (bcc)
B. Hexagonal close packed (hcp)
C. Face centred cubic (fcc)