Related Questions
What is the correct answer?
4
The atmospheric temperature during melting of ice/snow (in the atmosphere)
D. May increase or decrease; depends on the altitude where snow melts
What is the correct answer?
4
According to thermodynamic Fahrenheit scale, the fundamental interval between ice point to steam point is
What is the correct answer?
4
Larger length & diameter water pipes are made by
A. Electrical resistance welding
C. Semi-centrifugal casting
What is the correct answer?
4
Biological shield in a nuclear reactor is generally provided to protect against the
What is the correct answer?
4
Coarse grained steels have
B. No tendency to distort
What is the correct answer?
4
The dew point temperature lines on psychrometric charts are straight inclined sloping downwards to the right. When relative humidity of moist air is 100%, then
A. Wet bulb temperature=dry bulb temperature
B. Wet bulb temperature=dew point temperature
C. Saturation temperature=dew point temperature
What is the correct answer?
4
A compact estimate about the amount of materials handling between various work stations is obtained from the
What is the correct answer?
4
As per the Indian boiler regulation (IBR), the type of joint preferred for the circumferential joint is the __________ joint.
What is the correct answer?
4
Temper brittleness of a material can be fairly detected by the __________ test.
What is the correct answer?
4
Brazing filler metal used for joining steel plates
A. Melts below the melting points of base metals
C. Is copper phosphorous alloy
What is the correct answer?
4
Faraday's law of electrolysis is related to the
B. Atomic number of the cation
C. Equivalent mass of the electrolyte
What is the correct answer?
4
According to maximum shear stress failure criterion, yielding in material occurs, when the maximum shear stress is equal to __________ times the yield stress.
What is the correct answer?
4
Which of the following is an example of cathodic protection of metals against corrosion?
What is the correct answer?
4
Pick out the wrong statement.
A. For a pressure vessel to be classified as 'thin vessel', the ratio of wall thickness to mean radius is less than 0.1
B. For calculating forces and efficiency of riveted joint, either rivet diameter or rivet hole diameter is used in case of pressure vessel and in structural work
C. Longitudinal joint is normally made butt joint to maintain the circularity of the vessel
D. Maximum diameter of the opening provided in a pressure vessel, which does not require any compensation is 200 mm
What is the correct answer?
4
Photographic plates are coated with
What is the correct answer?
4
Which of the, following is not associated with the functioning of a petrol engine?
A. Compression ignition system
What is the correct answer?
4
A 2 kg object weighs 1.8 kgf on a spring balance. The value of 'g' at that location in m/sec2 is
What is the correct answer?
4
A semi-conductor is damaged & behaves like a conductor, on passing a strong electric current through it, because it heats up the crystals & breaks the covalent bonds resulting in __________ electrons.
What is the correct answer?
4
At absolute zero temperature, for any reaction involving condensed phases
What is the correct answer?
4
Vibration upto 100 kilo hertz can be most accurately measured by a __________ type accelerometer.
What is the correct answer?
4
The most suitable material of construction for a sewer to carry sewage under high pressure is
What is the correct answer?
4
The most important requirement for aluminium industry is the availability of cheap
What is the correct answer?
4
Unit of viscosity in CGS system is
What is the correct answer?
4
Minimum number of members required to form a Public Limited Joint Stock Com-pany is
What is the correct answer?
4
Broaching tools are usually made of
What is the correct answer?
4
Which of the following equipments is used for liquid dispersion?
C. Bubble cap plate column
What is the correct answer?
4
Annealing of white cast iron produces __________ iron.
What is the correct answer?
4
Basic open hearth furnace (BOF) is not used for producing __________ steel.
What is the correct answer?
4
Pearlite comprises of
A. 87% cementite & 13% Fe
B. 87% ferrite & 13% cementite
C. 93.33% ferrite & 6.67% C
What is the correct answer?
4
Globular form of cementite is formed during the __________ process.